Hotpoint-Ariston

After unscrewing the two screws from the body, the snail is not removed and does not open along the seam (both halves are stuck). Who took it apart, tell me?

Hello. Can anyone help, tell me the reason for the error F 15 on the Hotpoint-Ariston PMM brand HSF 03 T 223. This is the situation. When the night washing program is turned on 1. The drain pump starts for 15 seconds 2. The circulation pump starts for 15 seconds (the water inlet valve does not open, the valve is checked by a tester and turned on to 220 V, there is no voltage supplied to the valve...

Good afternoon.
PM Hotpoint Ariston LTF 11M116
When working, at certain points in the washing cycle it starts to whistle/squeak/howl. Not always. At this moment, judging by the sound, the inside is washed with water. Feature: if you press the back wall, the sound stops. What kind of thing can make such a sound. Pump? Or simply a loose fit of the tubes when supplying water to the upper basket,...

Good afternoon The Hotpoint-Ariston LST 41677 dishwasher draws water, heats and drains while selecting a program. But it doesn’t wash, i.e. does not splash water. What could be the reason? Is it possible to diagnose and repair it yourself? Drains the water as expected at the end of the wash. But there is no washing itself, just a program from start to finish, but the washing does not happen

Help with advice. After starting any program, water is pumped out, then water is drawn in, then after half a minute everything stops and 13 lights up on the display. I experimented: I removed the chip from the heating element, sat down with the cartoon and turned on the dishwasher again, the dishwasher started working, the voltage on the chip was 13 volts. I haven’t seen 220 volts even once since...

Please help with fault determination.

Given:
PMM Hotpoint Ariston HIC3B+26 (769991054232 / 869991054230) with a floating problem. After switching on, the resin regeneration process occurs, water is drawn in, the circulation pump turns on, runs for 15-30 seconds and stops. Waits 3-10 seconds and starts again. And so on endlessly until you stop it manually. During these switch-ons, the heating...

Good afternoon!

Sent after 9 minutes 33 seconds:
I have an Ariston Li-675 DUO, with an incomprehensible sore :
When filling it starts beeping..... It beeps three times and goes into error.
Sometimes it works fine. Sometimes it beeps three times, but then continues to work.
Of course, I checked the pressure switch! I also checked the circulation sensor (with a reed switch). The heating element...

Hello!
Dishwasher Hotpoint HIO 3C23 WF. Error 15. The error does not appear immediately. The machine starts the cycle, draws water, starts washing dishes, but stops with error 15. The heating element is working (checked for breaks and leaks). The wires to the heating element were also checked. On the board brains no no visible damage, swollen capacitors, traces of water, signs of oxidation or...

Hello. Can anyone help, tell me the reason for the error F 15 on the Hotpoint-Ariston PMM brand HSF 03 T 223. This is the situation. When the night washing program is turned on 1. The drain pump starts for 15 seconds 2. The circulation pump starts for 15 seconds (the water inlet valve does not open, the valve is checked by a tester and turned on to 220 V, there is no voltage supplied to the valve...

Good afternoon. Please tell me, I have the following problem. Dishwasher Hotpoint ariston HIO 3c23wf. Any program works for 5-7 minutes, after which a signal sounds and the washing process stops and the number of the selected program flashes on the screen. There are no errors (no salt or rinse aid). Help with a solution?

Apparently it comes complete with the door and is not sold separately. What can replace it?

Good evening, afternoon. The following situation arose: I noticed that the PMM began to tick on the left side. I removed the cover and started the wash cycle. I thought that the hydraulic seal was faulty. I ordered a new one. A new one arrived and the situation was the same.
ma63_-RHqrc

Hello.
Hotpoint-Ariston LST 53977. The indicators have stopped lighting.
If the machine does not turn on for a long time, then when you turn on the power button for a few seconds the indicators and buzzer work (sometimes you even have time to select the operating mode). Then they go out. The buzzer also beeps barely audibly. In complete silence you turn it on, select a mode and it works. The...

During the washing process, the 3h and 9h indicators start flashing. help identify the error.

Good day.
The lower door seal on the PPM broke. Can you tell me the replacement part number and where to buy?

Dear forum users. I replaced the bushings in the circulation pump cp035-005 with bushings from Zedex-100K and put it back together. The circulation and pressure are excellent, but the heating element does not turn on in any program.
The resistance of the heater is normally 28 Ohms
On the temperature sensor board (534232 / C00534232 / 488000534232) only a thermistor is soldered, which shows 420...

PMM ARISTON LI41, when the circulation pump is turned on, it turns off. The pump works directly without problems. LEDs do not display an error.

Having served faithfully for nine years (on average, one wash per day), the Hotpoint Ariston LST53977X 36702691000 dishwasher issued error code 6 - no water flowing. Having unscrewed the inlet hose, I checked the inlet filter - almost clean (at the entrance to the apartment there is a 400 micron mud filter, a Honeywell 100 micron backwash, coal and ion exchange resin). Putting the dishwasher on...

Good afternoon. PMM began to glitch. I was working on the same program all the time, I set it on a timer at night, and recently an error started popping up. By all indications, the aquastop is activated and water does not fill. The drain pump makes a humming noise at first. The pan is dry.

Another thing is interesting. I set the rinse to 8 minutes, after which the full washing programs work....

Hello. The following problem has arisen: the Hotpoint-Ariston LFF 8S112 machine inexplicably reduces the washing time. That is, a process is underway, the remaining time on the clock, for example, is 1:45, then suddenly it becomes 1:20. It seems that it is missing some element of the wash, but it is not clear which one. There is a tablet, there is salt, water comes in and goes out normally....

Good day everyone!
The machine began to show error 13. I found on the Internet that this heating element is faulty. However, having removed it and called it, I came to the conclusion that it was a worker. Resistance is 28 ohms, both fuses are working. I removed the control board, everything looked OK, nothing burned. I read descriptions that the contacts on the heating element relay were loose,...

Good afternoon.
Dishwasher hotpoint-ariston
A problem with starting began to appear periodically.
After closing the door, a sound signal should occur and the program should start (pumps, etc. are turned on).
But sometimes this sound signal does not turn on after closing the door and, accordingly, the machine does not start.
The machine does not produce any errors. The technician came, checked...

The dishwasher does not complete the wash cycle. The power button begins to blink, the number 15 flashes on the display. The machine makes a sound as if it cannot drain the water. What could it be?

Error 3 popped upWhat tell me, gentlemen, have you encountered this and how to treat it?

The reason the water does not heat up completely is because there is a problem with the program.

Good afternoon! Help me repair the Ariston LST41677 dishwasher. The circulation pump stopped working, bought a new one and installed it. I turned it on, it seemed to work, but the pump worked somehow in waves. After several starts, errors appeared (there is no display on it) but the on buttons blinked. first mode and third. Turned it off, then turned it on after a while. again, it doesn’t seem to...

Hi all. The following situation arose, the children pulled out the control knob of the program and threw it away. I found another pen from another PMM and now it’s not clear what program is turned on right now? Can someone from such a PMM set the program to 1 and pull out the knob to understand what position the regulator itself is in? Thank you

Good afternoon.

After the self-cleaning cycle in the dishwasher, the following element was found :
Stupid rules *x) do not allow you to leave links. in cross section is similar to the sign of the integral √. V-shaped element in black with a visor in gray. Stiffer than rubber.

Help me understand where this element comes from? He doesn’t fit anywhere. There is no other one like this installed in...

We install the built-in Hotpoint PMM, the facade on the door is mounted correctly, but does not allow the PMM door to open fully, it rests on the “false legs” in the photo, white (photo from the Internet, not mine, but the situation is the same) behind them are adjustable. What kind of false legs are these, what are they for, if the machine does not rest on them (when adjusted with normal legs....

The light went out while the machine was running. After that, in the middle of each wash, the machine pumps out the water, and then indicators 2 and 4 begin to flash. After turning off by pressing START/RESET, the machine turns on itself after a few minutes and begins to pump out water that is no longer there, and turns on these indicators. I didn’t find any information in the instructions. I...

Please tell me the location of the power supply and how to get to it. After a power surge (zero burnt out) it shows no signs of life. With electronics on You .

Hello. Can anyone help, tell me the reason for the error F 15 on the Hotpoint-Ariston PMM brand HSF 03 T 223. This is the situation. When the night washing program is turned on 1. The drain pump starts for 15 seconds 2. The circulation pump starts for 15 seconds (the water inlet valve does not open, the valve is checked by a tester and turned on to 220 V, there is no voltage supplied to the valve...

Good afternoon.
I had a negative experience calling a “master” through profi.ru. Not only did he break the drain hose, but he also scratched the kitchen floor, and that’s before even starting to repair it! *x) As a result, I refused his services, although he later sent the hose by courier.
I began to independently search for information on the Internet: my 7th program is blinking and does not...

Where to buy? I can’t find it

Tell me the error code, the 1,3,4 LEDs are blinking, the machine starts the cycle, and after a while it drains the water and the LEDs start blinking, I haven’t found any error code anywhere.

Without me, they dismantled and replaced the pump, the Ariston machine, bought a new one, but one of the connectors remains without a terminal. There is a terminal on the bottom one, but not on the top one,
Simply put, tell me how it should be connected, maybe there is a diagram or photo of the connection. Thanks a lot

I have an Ariston dishwasher. Today I opened it to check the salt and found a plastic part. It didn’t exist before. What is this? And action?

When the machine was working, periodically there was a smell of burnt wiring, I checked and found no reason. One fine day, there was a bang, smoke, and the machine was knocked out. When disassembling it, it turned out that the contact group feeding the heating element had completely melted. Help me find the reason.
At the same time, after the cotton and smoke, I turned the PM back on to the...

Hello. The dishwasher simply starts humming when connected to the network (it is turned off), here is a video with the sound of this process: xAQIjhMCI84
Washes normally, there are no errors and there haven’t been any, power supply 220-230V, normal grounding, water: pressure, hoses according to instructions, etc. In general, everything is ok, but it buzzes when the power supply is turned on....

Tell me where I can buy such a board? I can’t find it anywhere

Good afternoon, please help me figure it out. When you turn on the machine, after a short period of time the wash and end of cycle indicators light up. Having surfed through various forums
they looked at similar topics, they write that these are problems with the breakdown of the circulation unit, somewhere there are problems with the washing chamber, etc. .d. The circulation block was...

Good afternoon. The dishwasher began draining water immediately after filling, indicators 1 and 3 were flashing. Moreover, if you open and close the door during a fill, the cycle proceeds normally, either until the end, then until the next fill... I took it apart, no leaks are visible. Where to dig? Thank you.

Hello, please tell me what could be the problem. I’m happy with the dishwasher. I use 1.5 g. But the other day, constant shutdowns began when you set the timer at night. I turned it on in the evening and set it to delayed start. After a delay, it turns on and begins to draw water. then he throws in a tablet and after that I don’t know how long it washes, but it turns off and starts beeping (but...

Good afternoon There is an old Ariston L63 on the farm, it works as usual, it carries out the program, the lamps do not show errors, but it makes terrible cracking noises during operation. Video with the work process and cracks
N-4eeqGqzmU
y_Gb2Q3CPho

During the washing process, the machine stops.
The power indicator blinks, code 13 is displayed. The cuvette with the powder is closed, it heats up the water (tried to start a self-cleaning cycle).
Looks like this KG5_bdiSYx8 , only the model is different.

How to treat?

To replace it, I will buy a non-working Askoll M233 pump with an intact magnet on the shaft. The condition of the bushings and windings does not matter.

1. The hose leading from the circulation pump to the plastic tube on the back wall, which leads to the impellers, burst. Symptom – the machine constantly works to drain. There is water in the pan, the third indicator from the left out of six is ​​blinking. The hose was replaced with a piece of antifreeze hose of suitable diameter from the nearest auto store for mere pennies. A suitable one was...

Good day, dear ones.
There is a Hotpoint 3c26 PMM. It was purchased in March 2020. It worked fine for about three or four months (well, as normal, we only used the ECO mode at night, and, let’s say, the QUICK MODE washed for the wrong 27 minutes, but could have lasted for an hour or two, the remaining time was counted down to 6 minutes , and then it just stopped, but since the main mode in which...

Hi all.
Machine LSI 48A (Ariston). When starting, it drains and fills with water, but the recirculation pump does not start, it hums. I took off the side walls and took a look. The winding (as far as I could see) is intact, there is no stink. Could the reason for the non-start be in something other than the motor itself, for example in the capacitor? How to check it (conder)?
Thanks in...

Dear forum members
I own an Ariston exilia Li 68 DUO dishwasher. Recently I encountered a problem with water leaking from my car, after disassembling it I realized that the circulation pump volute was leaking. I ordered the snail 07003486 according to the number indicated on the removed spare part. But the trouble is, a snail of a different design arrived, but with the same number. Question, if...