Midea

Good afternoon.

Weissgauff BDW6062 D machine. If I understand correctly, the same Midea. Correct me if I’m wrong.

New. She stood there for a long time. Plugged it in, water poured in. After a couple of minutes, it drains the water with error E1. There is water pressure. The hose was suspended by 40 cm.

It turns out that the circulation pump does not start. Could it jam during downtime?

I ran out of salt, I poured it in as per the instructions, but the indicator was still on. At the first start it was the same, but then the technician came from the store and that’s it, the indicator went out. The reason is not clear.

I found a gasket in the filter. Exactly the same one is located where the atomizer connects to the body. But it has a slightly smaller diameter. Where could it have fallen from? Or were there 2 of them and this one just stretched out? Can anyone tell me how many seals there should be? Model mid60s100

Dishwasher Midea. Only the power button works adequately, most do not. Programs do not switch, the cycle does not start. The door closing sensor is triggered by pressing the incomplete load button. The buttons are all working, there are no “stuck” ones. Model MFD 60S320W

Dishwasher year. Not long ago, a white coating began to appear on the filter after each wash, feeling like grease. Easily washes off in the sink with dish soap and hot water. But it never existed before. The dishwasher is used very carefully. Salt, rinse aid, monthly cleaning. I didn’t change the dishwashing liquid. What is this??

Hello!
The top sprinkler fell off, it was small, I don’t understand how it stayed there. Now you can put it on the plastic pipe, but it barely stays there. There are no rings or fasteners lying around in the car. Please advise what can be done, and if new spare parts are needed, where can I buy them in St. Petersburg? Photo attached.
Thank you! 11.jpg 22.jpg

Help me buy a basket for the Midea MCFD55200W dishwasher

The four right indicators began to flash alternately. There are no visible defects inside. The mesh in the hose was cleaned. The drain pump is working. There is no water in the pan. After disassembling and reassembling everything, it started up once. I washed it for 20 minutes, drained the water and again the four indicators flashed alternately. Has anyone encountered this? Where to dig?

Hello everybody. Please tell me there was a hum in the pump area, the condenser was changed, but after a couple of washes it started again, please tell me what the problem could be, thanks in advance.

Hi all ! The middle Inno wash sprinkler (midea mid60s900) began to rotate poorly. I took it off, there were no deposits, I put new O-rings on the pipes, the rocker arm barely moved, and the lower sprinkler rotated like a rocket. The only thing I see is that play has appeared (it sways quite a bit horizontally), but there is no wear visible to the eye. What to do ? :sorry:

Good afternoon everyone. Does anyone know what this leak is and how to fix it?

Good day! In general, the washing machine is MCFD 0606. The water leakage error comes on consistently once a month, accompanied by water leakage from under the machine. Contacting the service center did not solve the problem. Subsequently, I called the craftsmen to the house. The problem was not solved. Water flows steadily, once a month. When removing the pan, I do not observe any obvious leaks...

Hello. Performed preventive cleaning of the dishwasher Midea MFD45S400W using Finish cleaner. After finishing cleaning, I found something like a plastic washer on the filter. I looked all over and still didn’t understand where it came from.

I include Midea 45 cm MFD45S110WI. After the first start, the indicators began to blink: WiFi program indicator Program indicator 90 min. I tried to reset the program: I unplugged it for 15 minutes and held the Power on button for a long time. Useless. The indicators are flashing. The technician came and looked and there was no leak. I turned on the program for 90 minutes. The dishwashing process...

Hello, dishwasher Midea (standing in the kitchen), I started the dishwasher, everything was fine, but after 10 minutes it issued f4 first, then I decided to turn on off, and already issued the e4 command, before that there was a situation in the bathroom, the water was not flushing well, there was a blockage, I I tried to clean it, the pipe is common for drainage, it turned out that there was a...

Good afternoon. The door began to open very hard and at the same time there was a grinding sound of a spring or something else. My husband took off the case, everything went away, loaded the machine and everything came back again. It seems to me that the door has stretched, i.e. While you are loading it, it takes on the load and something is stretched.

The brine valve is constantly open. (water fills the salt container from the beginning of the cycle). How to check the valve? - winding resistance?, Supply voltage?

Midea mini bug e1

Good afternoon!

Please tell me, is the inlet hose with aquastop suitable only for the original one or can I buy it from another dishwasher? And is it possible, instead of a hose with an aquastop, to buy an aquastop itself, install it in the dishwasher, and attach a regular inlet hose to it (like for washing machines)?

Thank you!

Good day. the problem is this. We bought a PMM (Midea mfd 45s320 w), a technician came and installed the PMM through a tee to the hoses of the washing machine. He said that it would be easier and just as functional. I, as a person completely ignorant of all this, agreed. checked on site. the water filled up and drained, then the program was turned off. Today I loaded all the washing supplies,...