Electrolux

Product , Good afternoon, tell me the values ​​of the resistor R3122 and the capacitor below C3075, it looks like

Sent after 1 minute 41 seconds:
ig_nat , Good afternoon, tell me the values ​​of the resistor R3122 and the capacitor below C3075, it seems

You have demo mode enabled, disable it

Check the pressure switch and its chamber, you have an overflow of water.

Here you need to describe the process in more detail, if the program had not started when the door was closed, then you would not have collected water. Now the following is interesting: when the door is closed, water is pumped out, and then water is collected and then there is silence?

The problem is definitely most likely in the board, there are two identical machines, one has the same problem, but if you put a known good board on it, then the machine works without any problems. So far I haven’t found the reason either, I blame the firmware, but if yours was sewn and there is no result, then you need to try to look for the problem in the module itself

I have the same story, the chip on the heating element when I call shows 035 v

Didn’t find a solution?
I have the same problem

Hello, same error and all the same symptoms. Did you manage to do it or not?

Water in the sump, aqua-stop has tripped

On November 13, 2023 I wrote a question and no one answered anything. I solved the problem myself. There was a problem: when the PMM is plugged into the socket, the water inlet valve immediately activates and does not turn off. Replacing the TY 3001 semistor in the circuit for switching on the water supply valve, then replacing the resistor R3163 with a nominal value of 47 Ohms (burned out),...

The machine will show errors only in service mode, and when you have the same error it will be easier to repair. Or dance with a tambourine, remove the wall, check the heating element, if the heating element is working properly, check the Megaohms for leakage to the body, if there is a leak, there will be no heating. But it’s better to start with the error that is in the dishwasher’s memory

It looks like the reason is in the display board (touch buttons), the firmware has crashed... In Russia, as it turned out, no one is flashing... I’ll have to buy it - and it costs 12 thousand... It’s a shame. It’s a shame that the company itself doesn’t even bother to service its own equipment, and yet so many of them are offered for sale!!!

Sealing it with sealant helped for a while, but recently it started leaking again. I decided to try to cover it up again - it didn’t work at all. I waited more than 24 hours and turned it on - it immediately started leaking. What could be the problem? Why doesn’t it even stick to silicone anymore?
The best solution is to find a similar one seal from Ariston (namely Ariston, not Hotpoint) you can...

Entered service mode using brute force method

In the service manual 44 is described as a strong/or weak signal from the Pressostat (read it a long time ago)

have you overcome the problem?

If the motor hums, then: There is a blockage in the hose, sewer, the drain motor is faulty

Good afternoon, the de dietrich dvh1180gj dishwasher has switched to demonstration mode. how to turn it off? Pressing the start button for 3 or more seconds does not help; there are only 4 keys on the sensor. Trying different clamp combinations also did not give results.

Sandroe
 Re: The circulation pump is leaking(?) Quick quote
Message April 03, 2021, 07:29 pm

Finally got around to it. Everything is as in the video: all gaskets are intact. I washed it and screwed it back on. Not leaking yet. Thanks for your help!

Help!!!)

Good evening. how to check whether there are errors on the electrolux esf9552low dishwasher or not? Thank you.

I found the answer on the forum. It helped.

« Press the Auto Sense and ECO buttons simultaneously for 3 seconds. The display should change from d:On to d:Of

Good afternoon The Siemens PMM is more than a year old; when selecting a program, after a few seconds it gives a signal and no water flows. We checked everything (hose, filter), replaced the aquastop, but the PMM does not start. We connected it to the water supply on the street - it works there. Why doesn’t it work in the house? The water pressure is good.

Well, if there is no blockage in the filter, hose, siphon or in the drain route, then check again that the drain hose is connected correctly, there should be no creases or kinks, the height of the drain hose connection is at least 50cm from the floor)

Good afternoon!
I have the same problem (36V on the heater).
Can you tell me if flashing/repairing the control board helped? Which board was repaired, the one that directly supplies voltage to the heater (in my case, it is installed on the rear wall at the very bottom)?

squeezed out the gasket of the receiving plastic bowl of the pallet, adjusted the gasket with a screwdriver (you can use tweezers, pushed it into the groove...) into place, - normal flight !!!!

Please point your finger at where this pressure switch is hidden.. I think I found what it looks like and is on sale, but I don’t see it at home)))
IKEA SKINANDE(Elektrolux) 911536047

Hello everyone! I had a similar problem a year later... And I found a solution. I removed all the filters and sprayed anti-grease into the machine where the filter was, waited 15 minutes and put the machine into operation without a filter and without dishes))) AND VOILA! EVERYTHING IS WORKING!!! The filters also need to be washed properly 😉

Needs lubrication

Check the heating element for breakdown. Perhaps the protection is triggered.

Look at the varistors in the boards of old radio equipment (TVs, for example) and do the first switching on through a 220V incandescent lamp.