Beko

Good evening!

I ask for help with repairing the Beko DIN 1531 dishwasher. In any program (including a 15-minute rinse with cold water) it behaves as follows: drains water, pours water, pause for 30 seconds, pours a little more, pause for 30 seconds, pours a little more (already up to the max level, no more), stops. The timer does not decrease, nothing happens (we waited a very long time).

At...

Good luck to everyone.

Forum members, please tell me.

The upper rocker arm has stopped rotating. The jets flow through it, and not weakly.
The pump seems to be working normally. But something is still preventing the rocker from rotating.

There is a suspicion that the fluoroplastic gasket at the point where the rotating
part is attached to the stationary part has worn out. Although, it feels...

Good afternoon everyone. The situation is this, the Veko dvs1300 dishwasher freezes in one place when washing dishes, the pump works with a break of 10 seconds, and so on ad infinitum, while three lights blink. Cleaned the filter. Can anyone tell me where to look for the problem?

The dishwasher is two years old. It began to leave a strong white residue on the dishes. The indicator lights up indicating that the salt has run out. Added a full tank of salt. After two washes, the indicator is on again indicating that the salt has run out and again white coating on dishes and on the walls of the dishwasher. The salt tank is screwed in well. There is a rinse aid. I use finish...

Hi all. The BEKO DIS 26012 was leaking, for some reason it was leaking from the standard hole, I couldn’t find any plug. Tell me, should there be a plug there or is it leaking because some channel is clogged?
I am attaching a photo.

The PMM draws water and then stops - the circulation pump motor hums and does not pump water. I noticed that the spring-loaded impeller inside the volute is not fully pressed, the latches do not completely come out of the grooves, as a result of which the impeller in the volute jams, the engine cannot spin

Good evening! PMM Beko din 15210. A problem has arisen: after washing the dishes are all covered in salt. I checked the regeneration valve, I thought there was a problem with the spring, I stretched it a little, it didn’t help. I rang the triacs in the control unit, everything is fine. Next, I launched a short washing program: the machine fills with water, heats the water - the water is not...

Good afternoon.

I ask for help. I can’t pull out the drain motor, the latches are in the way. Does anyone know how to extract it?

I found a broken ring, can anyone tell me where it came from?

Hello. Beko din 5835 dishwasher. The actuator broke (the motor burned out). I replaced the motor. I installed it on the machine, it doesn’t work.

Hello everyone, the motor of the water distributor valve has burned out, I’m looking for the motor, I can’t find it anywhere, has anyone replaced it or found one for sale?
It is found in many devices

Sent after 3 minutes 48 seconds:
Does anyone know if it is possible to replace the valve assembly itself with another one? There is a seat model the same as at my valve

Good afternoon My beko dsfs 1530 took on a full tank of water and started leaking, I plugged it in, the pump turned on and won’t turn off. This happened half a year ago, a week later she came to her senses and started working. Tell me what to do?

Good afternoon!
I am asking for help with the Beko DIS39020 PMM.
I replaced a burnt-out heating element myself, after which the PMM began to buzz loudly. The lower PMM pan hums directly during the main operating mode, which I removed to get to the heating element. If you press the pan upward with your hands more tightly, the hum stops. When assembling, I tightened all the screws of the pallet...

Hello, a question about the dishwasher. Model Beko din 28320.
When you select any program, the program cycle just starts to start, it gives error e 02, and there is definitely water in the system and the pressure is normal. If you open the door and close the error, the program continues to work, but almost after that it starts to show error e 01, which leads to the beeping and the program ending....

Hello everyone.
PPM Beko dsfs 1530
This problem has stopped showing the indicator that the rinse aid has run out. Previously, everything showed.
When adding rinse aid, it either stopped showing or still remained on. And then suddenly it stopped burning, although I know for sure that the rinse aid has been gone for a long time.
Can you tell me where to dig, maybe someone has already had this?

Guys, tell me if anyone has encountered this. I have PMM the following problem appeared. With the door closed PMM Beko 5930 clicks in the area of ​​the control unit and the aquastop vibrates, while the button on the machine is not turned on, but the machine is plugged in. Now if you turn on the start button, it knocks out the RCD (automatic machine) in the apartment. Thank you in advance!

Hello. Dishwasher Beko DIN24310 The question is, can the water itself drain during washing through a drain hose, such as a self-draining hose, if it is not properly connected to the sewer? The hose lies on the floor and goes directly into the sewer pipe. The pipe is raised from the floor by 10 centimeters. During washing, the following happens. The machine fills with water and starts washing. If...

Hello.
Please tell me why the top of the door is leaking?
I changed the seal.
The upper sprinkler too.
It leaks without the lower sprinkler.
If you remove both, no.
WhatsApp Image 2022-05-08 at 21.41.19.jpeg

Help me to understand. PMM Beko dis 28140. In all programs, the washing time takes much more than stated in the instructions and indicated on the display. For example, on program 7 at half load there should be 30 minutes of work, but in reality it takes 1 hour 10 minutes. Thanks in advance, Alexander.

Good day, Beko DIS26012. There is a white coating on the wall. What could be the reason?
NPcdsJDb_6E.jpg

Good afternoon,
Machine dsfs 1530. p1 and p3 flash simultaneously. When you press the start button, p1 and p3 are constantly lit. Doesn’t respond to button presses.
If you press and hold the start button and press on, after three seconds all the LEDs blink, if you press start again, the machine starts draining, you can hear the pump and circulation pump operating, the sound is normal. After...

Hello. Machine Beko DFN05310W. Worked great for 2 years. Now, when drawing water, water flows from the upper ventilation of the hydraulic distributor. You can get rid of this only if you reduce the water supply pressure by closing the valve on the cold water inlet pipe. But the dishwasher takes a very long time to fill with water. Before this, everything worked with the tap as open as possible. I...

beko dsfs1530 the p2 indicator flashes when turned on, does not respond to any buttons, after pressing start, the indicator stops flashing, but nothing happens

Hello!

The dishwasher has stopped draining water. Instead of draining, the pump is humming (?). And the car got very hot, so that you could smell the smell of burning plastic (it was a melting horn (?) on the back wall). Analysis showed that there was no blockage in the drain system. The pump impeller rotates with a springing effect.

Here’s another strange thing: the presence of liquid of an...

After washing, the dishes are all salty and the salt icon is lit. I added 1.5 kg of salt before washing. Please tell me what could be the matter.

Hello.
Dishwasher DFS25W11. I can’t adjust the water hardness level (it should be minimal), because... If, according to the instructions, you press the start delay and P+/P, and then P+/P, then what appears on the display is completely different from what is in the instructions. When you successively press the start delay button, instead of r1-5 the following appears: 1 - HFt, 2 - 1Ft, 3 - 5Ft. 4...

Good afternoon. After the rocker arms start, the dishwasher stops after a couple of seconds and starts them again, and so on for the entire time allotted for the rocker arms to work. As a result, the time allotted for their work, she tries to start them. Water is supplied and pumped out. The heating element works and does not display any errors. What could it be?

In the eyelid machine, when you select any program, it works until the moment when the rinsing cycle should begin, and then it displays error e02. When choosing just the rinse mode, sometimes it works for a couple of seconds, and the same error. Everything is definitely ok with the inlet hose, and with the water pressure in the system, the pump is new.
What could it be?
Could it be a fluometer?...

Hello, a question about the dishwasher. Model Beko din 28320.
When you select any program, the program cycle just starts to start, it gives error e 02, and there is definitely water in the system and the pressure is normal. If you open the door and close the error, the program continues to work, but almost after that it starts to show error e 01, which leads to the beeping and the program ending....

Hello.
Dishwasher DFS25W11. I can’t adjust the water hardness level (it should be minimal), because... If, according to the instructions, you press the start delay and P+/P, and then P+/P, then what appears on the display is completely different from what is in the instructions. When you successively press the start delay button, instead of r1-5 the following appears: 1 - HFt, 2 - 1Ft, 3 - 5Ft. 4...

the pump does not turn off

I think the problem is that the impeller does not spin (most likely a blockage). how to remove the plastic thing (which goes to the drain) to check? Thanks everyone in advance

Gentlemen, I am asking you an age-old Russian question and a request for help answering it - WHAT TO DO?
Problem with PMM beko dsfs 1530:
When the power is turned on and the door is closed, the water pump starts working . So it (the pump) can work for a very long time (I checked, i.e. I waited quite a long time, and also simply poured water into the PMM manually), and it can only be stopped by...

Dishwasher beko ddn 5832 x. The Aquastop worked, since the water did not fill, but the pump was working, I turned it off, unscrewed the front bar - Water in the sump. I removed the water, disassembled the car, it turned out that the water had been leaking for a long time, as there was a corresponding sediment on the parts. Question: where can the leak come from if water has settled on this spare...

Beko dishwasher is new. Water hardness is 2, the salt indicator is constantly on, I added half a pack of salt, as a result the dishes are white and salty after washing, I use finish all in 1 tablets, maybe I don’t need to add salt? If you don’t add salt, the dishes are perfectly clean. I couldn’t find a description of how much salt to add either in the instructions for the machine or on the salt...

After a small flood caused by neighbors on the top floor, the machine stopped working. After selecting a program and starting it, as always, the water drains, then it fills up and then nothing happens, in any program, I waited a long time. If you click on cancel the program, the water is drained.
The first time after the flood, the flow sensor worked, but there was not much water in the pan, it...

Hello. From the title it is clear that it does not heat the water, but the heating element works. Its resistance is 29 Ohms. The temperature sensor at 22 degrees showed 44 kOhm, from the freezer 165 kOhm, and during measurement the resistance dropped as it warmed up. In hot water 18 kOhm. I think it’s a worker. Please tell me in which direction to move next?

Good afternoon
BEKO DSFS 1530 I start the program the pump ruins but the water does not flow, tell me it’s probably the valve?

​The PMM began to take in more water than needed, and not immediately.​ As a result, the excess water is drained into the pan, the leakage sensor is triggered and the water drain is turned on. As far as I understand, there is no water level sensor in this model? Is the flow regulated by a flow sensor? Is it not working correctly? Is there any way to check it? Or is that not the problem?

Dear forum users, I am asking for help in repairing the beko DSFS1530 dishwasher. When turned on, the machine begins to emit a sharp buzzing, slightly vibrating sound, similar to one of the plastic gears cutting teeth, and the whole one slipping at the cut points. The impression is that the sound is coming from the door or from the right wall of the machine. The signal lamps light up as during...

I ask for help)
I stopped drawing water... You turn it on, drains the water, but there is no flooding, then there is silence.
I decided to check the aquastop. Blocked, applied voltage directly to it, does not open. It turns out that this is the problem?
I also tried to connect the hose directly to the dishwasher, water flows, but the flow does not stop. There seems to be a valve there for the...

Hello guys, maybe there was such a topic, I didn’t find it, the three-way pump in the dishwasher burned out and the board burned out from it, I bought a board, connected it, the result was zero, the panel lights up, the programs turn on, turn off and the washing process does not start, it doesn’t even draw water, I bought another board and the same problem , please tell me what else the problem...

Previously, when I added salt, when I opened the lid, a little water flowed out and the tank was full of brine. It’s completely dry there now. what could it be and what should I do about it?
Washes well so far.

Help!!! The salt indicator came on. We fell asleep and turned it on. Salt deposits, you have to rinse 10 times. Over the past 2 weeks, we’ve already fallen asleep 3 times!!!! packs of salt, but the result is the same - after the first wash the indicator lights up again and until the salt is washed out of the machine, a white residue remains. Maybe I shouldn’t bother anymore - wash out all the...

The dishwasher has been in use for just over a year. After the start of operation, the water hardness value was not set - as it was by default - and it worked. The tableted product ALL in 1 Somat was used. The first months of soap were excellent - the dishes and the dishwasher itself were shining.
It should be noted that the water hardness is high. I don’t know exactly how much - but at the...

Kept it in the garage. I was freezing. Brought it and connected it. It started leaking. Even when pouring water into the salt tank, the water leaks.
Question: Is it possible to repair (glue) the tank or replace it? The price of the issue is very high (tank 2000 + repairs 2000).

Hello. Model DSFN 6630 min. until the end. Is this a glitch???