Discount

After washing the dishes, a small rubber seal was found at the bottom of the machine, I couldn’t find where to install it, can anyone tell me.

About two months ago we bought and installed a machine at our dacha. I worked several times a week. Today we loaded the dishes as usual, threw in a tablet, the rinse aid and salt levels were normal. We started it for 90 minutes (we often set this program, because the dishes are usually not very dirty). At first everything was as usual, it was working and rustling there, and after about 40 minutes...

Good afternoon!
Please tell me which model of drain hose can be used for the Korting 45165 dishwasher.
The machine began to leak and displays error e4. The machine has not been fully checked yet, but to the touch it feels like the drain hose is cracked.
Thanks in advance for your answer!

Good afternoon. The Kerting dishwasher draws water, and that’s where its work ends. I open the dishwasher and there is water in the tray. If you turn it on and off, the water is drained and again collected in the pan. Tell me what could be. Filter is clean

Dishwasher Kerting 60165, the door does not lock when open. I took it out and disassembled the sides, and it turned out that the roller, which is part of the door tension mechanism, had been torn out of its seat. Who came across it? Who worked on collective farms?

During washing, the dishwasher makes several clicks, somewhere in the middle of the cycle, and on the same program, it can make different clicks, sometimes three, two or one, and they sound different. The dishwasher is new, we’ve been using it for two days.

Friends, if anyone has instructions for this shaitan machine, please give me, otherwise for the third day I’m poking somewhere, the result is zero

When the dishwasher is empty, it completes the entire washing cycle. As soon as you fill it with dishes, error e1 lights up when filling with water.

Hello. It leaks through the dispenser seal on the PMM KDI 45570 and I can’t figure out how to remove it. Could you explain to me how it is attached and how it is removed. Saipu dispenser number model sp-d02b.
Thank you.

I have a korting kdi 45165 dishwasher being repaired, it’s not a trivial problem. I start the washer, the first time it works fine, it drains all 3 cycles, as soon as you start it 2 times it stops draining completely, sometimes it doesn’t even drain the first time. The frequency is not clear, but most often it works fine once.

We cleaned everything, the drain hose (the drain pressure is great)...

Hello, dear forum users.
Please tell me if anyone has come across this.... I’m looking for seals (gaskets) for the upper sprinkler. I got the impression that they are on sale for any PM, but not for Korting.
Who bought it and where, maybe from other PM, are these rings suitable for Korting PM?

Good afternoon, forum members. This is the problem: the PMM turns on, draws water, but does not wash; after the time allotted by the program has passed, it completes the cycle, leaving the dishes in the same condition. Please help

Good day, I would like some help on this issue, I have a korting 45165, error E1 periodically occurs after about an hour of PMM operation (program for 1:30 hours)
there is water in the pan, after emptying the pan by hand using a mug , I run PMM and everything works fine, I can wash the dishes 2-10 times and the error occurs again, I removed the side panels, ran a 15 minute rinse, everything...

We bought and installed the car and used it correctly for 4 years, everything is Okay! But the day before yesterday the E1 error appeared for the first time and the water is not draining and there is water in the pan, what does this mean? Who had this happen, if so, how did you overcome this error? Thanks in advance to everyone!

Hello. After turning on the program, the drain pump is activated, after which the valve opens and water begins to flow in. After 2 minutes, error e1. water pressure of about 3 kg. the pan is dry, i.e. The pan sensor is open. I found a filling unit - there is an impeller in it that is spinning. 5 volts come to the impeller. but what comes out of the turbine is some uncertain 0.2-2.6V. why are they...