Other manufacturers

I want to buy a Hyundai 480
there is a question: what will happen if the water turns off during the washing program?
it is clear that there will be an error E1, but what needs to be done after the water is supplied?
restart the program washing according to a new
click continue program, if there is one
it will understand that there is water and continue

The PMM VVK collects water and stops. Imitating the operation of the pressure switch by closing the contacts during the process of drawing water does not change anything (only two contacts). Where to look?

Hello. Help with a question. Along with the kitchen, a new Haier hdwe9-191ru was installed; during operation it has an incomprehensible problem, namely, steam condenses in the sides of the door and settles on nearby doors and niches. For my part, I even adjusted the seal, pulled it out a little, but it didn’t help. What could it be connected with? There is a feeling that steam is escaping at the...

Hello everyone!
Pmm it started to wash badly. I ran the diagnostics and everything seemed to be normal. But! Measuring the temperature using a thermocouple on a multimeter, it turned out that the heater heats up to a temperature of 70 degrees and then turns off. The temperature drops to 24 and that’s it. Then at the end of the cycle it heats up again to 70 and turns off again. At the same time,...

Good afternoon.
The machine is only half a year old, it worked just fine from the start.
A month ago it started not heating the water, and subsequently did not wash the dishes.
When you start it a second time, let’s say 90 min. (the same dishes, without a tablet) there is heating, but they are as they should be (straight steam with a rocker)
But again, for no apparent reason, it started working...

After working for 2 years, the car began to leak water from under the door. At the same time, the water rises along the felt noise inside the door and, apparently, short-circuits. The machine may turn off and then won’t turn on until it dries out.
The rubber seals are normal, the drain filter is clean, the impellers are intact, but the problem is not solved. What else to see?

Hello!
Maybe someone has encountered a similar problem or knows where to dig.
I always wash dishes in the auto mode. A preliminary estimate of the cycle time of the PM itself is 2 hours 10 minutes.
Sometimes after about an hour of washing, the machine stops the cycle (drains water and opens the door as at the end of the cycle). In this case, the end of the cycle timer always shows 30-31 minutes...

Good afternoon, question about the Schaub Lorenz dishwasher.
At one point, I filled up a whole tank of salt as expected.
At the end of the wash I decided to check the salt, but it was not there, apparently it had gone into the sewer, I noticed a strange noise from the dishwasher. It turned out that the valve in the photo was humming.
Good people, tell me what to do

Good afternoon, forum members. There is a hole in the dishwasher, please tell me who knows the reason! The machine has been in operation for 3 years, warranty 2. Manufacturer: Zigmund & Shtain

Hello, we bought a new Hi dishwasher, installed it, connected it, and the machine smelled like sewage. It looks like the smell is coming through the drain hose, what should I do?

The dishwasher draws water but does not wash. after a while the water drains. the master says circulation pump. pump price new 13k used 8k. Does anyone know if anyone can plug in any engine?

Hello friends.
Please tell me about this dishwasher.
After starting the washing program, the pump starts pumping water and does not stop. Water begins to flow out from under the door, everything flows into the pan. In principle, there is no emergency flood sensor in the pan. The float with two limit switches appears to be normal, the limit switches work. True, one is connected as normally...

Tell me what is the name of this white thing?
Water is collected there when the dishwasher is turned on. Usually, when it reaches a certain water level, it should stop filling, but the water does not turn off and flows over the edge.

A month ago we had the same problem, we changed the pump and cleaned the hose where the water comes out with waste. Everything was great. Now again

What could be...

Good afternoon!
I ask for help from experienced resuscitators PMM. The problem is this: there is a Zanussi ZDT92200FA pump, a pump, as I understand it, a disposable Blackmann one. The impeller fell apart into two halves, at the moment I tied it together with a thin plastic tie (which is used to tie electrical wires together) through three holes at the base, now the machine pumps like new. But I...

Experienced Gurus, please help, the PMM is flooding through a hole located on the left wall; a regulator with positions 1-2 is installed on it; it is in position 2, after I restored the operation of the input E/mag. valve stopped working water heating

Sent after 1 hour 16 minutes 10 seconds:
The heater is working, the machine is murmuring as if there is air in the system. When turned on, it...

Hi all! The glass washer does not always see the water level. If specialists?
Restaurant equipment. Mash company

Has anyone encountered a PMM control failure? The washing cycle times are disrupted, the water temperature does not rise above 35-40 degrees. I took it to the service center under warranty, it stayed there for 3 days, they returned it and they said that the device was fully operational. After this, the PMM worked normally for 2 weeks, and here it is again. I suspect that the service reset the PMM...

Help, what kind of error code is displayed on the PMM Medalstor Ikea display?

Hello! Stopped shooting tablet in the process of washing dishes. I took the door apart. I examined the contents. I rang the coil - 1333 Ohms. Everything is bad? The wires suitable for this coil go somewhere under the bottom of the machine. It’s worth going there and seeing something. If yes, then what? In general, I don’t understand anything about these matters. Or is it easier to order and...

Good day everyone!
Please give me some advice.
All of a sudden the machine started turning on/off spontaneously. The display lights up, but the program cannot be selected and started, after some time the machine turns off.
If you do not disconnect from the power, it will turn on and off. The nearest services are extremely far away.

Direct your thoughts, if possible, in which direction to look for the breakdown?

Dishwasher Weissgauff DW 4012 starts to work properly, but after about an hour of operation, in a heated state, it suddenly shows a squeaking error - icon rinse (according to the instructions - this icon also means an error code: lack of pressure in the water supply system or a faulty filling valve). But the...

Sometimes it heats the water, sometimes no , stopped finishing the wash, stops washing randomly, then after 10 minutes, then after 30 and stops with the power button blinking and the first (ECO 50) and third (45 for glasses) buttons light up, what is the error, or Has anyone encountered such a breakdown?

Hi all! zanussi ZDI101X The truth is somewhere nearby, but I just can’t find it. Everything started well. During the inspection, it became clear that the microphone in the door opening mechanism was broken; the machine considered the door open all the time. I block the microphone so that the door is always considered closed. I check, it starts to wash. Hooray! I turn off the program, assemble the...

how to remove/replace the ion exchanger on a dexp m9c7pd dishwasher

Hello everyone!
Pmmm started to look like a wash. I ran the diagnostics and everything seemed to be normal. But! Measuring the temperature using a thermocouple on a multimeter, it turned out that the heater heats up to a temperature of 70 degrees and then turns off. The temperature drops to 24 and that’s it. Then at the end of the cycle it heats up again to 70 and turns off again. At the same...

Hello. The pump on the Ariston dishwasher began to jam, replaced the graphite bushings, assembled it, applied 22, it works, screwed the heating element into place, let it go, it works. I stuck my finger through the pipe in the heating element, twisted and spun, applied 220, wedged. 2 days I don’t know what to do

Falling asleep salt into the dishwasher, vestel cdf 8646 ws, I start the washing mode and after 5 minutes it again shows that there is no salt in the machine. There is a white coating on the dishes after washing.

Greetings to everyone!
On the AKPO ZMA55 dishwasher, the salt indicator lights up after several washes. When you open the lid of the salt container, water flows out. The last time I didn’t do anything, I just opened the container, the water flowed out - I closed it. After that, the indicator went out.
A couple of simple ideas - too much salt? Or do the washers need to reduce the water hardness in...

PPM samtron is flooding, error F5 appears, all indicators start blinking, is it draining?

Starts any cycle and stops after 90 seconds

Hello!
Please help!
NEFF dishwasher. The light indication does not work; the pump turns on periodically. It is not possible to reset and reboot using the buttons. Unplugging for a day didn’t help. Without a scoreboard I can’t determine the error. A year ago this happened due to a leak, but then there was an indication and the error was identified. Now it’s different.
What could be the problem?...

Those. as if the door closing sensor does not work.
Has anyone encountered this?
Call a technician and change the sensor or look at something else? All hoses, hidden filters? Maybe something else is causing the launch of programs and the squeaking sound when the door is closed? TEKA machine, 5 years old, but we don’t use it often, 1-2 times a month, not more often.

Good day to all. There is a dishwasher built by Weissgauff (unfortunately I don’t know the model), which leaves water in the tray after the cycle. Previously, I drained the water completely. The filter is clean. The motor is working. The hose is clean. During the next wash cycle, it drains the water as expected at the very beginning. And this water drains completely. But then it remains. Can...

Good afternoon. Please tell me if anyone has encountered such a problem, since the Internet did not help. Toshiba dishwasher, recently a problem appeared with the rinse aid compartment. After washing, the rinse aid and water are mixed in it. After each wash, its quantity does not decrease, there is simply more water. Even if you completely pump out the liquid from the compartment, after washing...

Dishwasher candy CDI 45
The operating mode selection sensor does not light up
How to restart the machine?
What to do?

I couldn’t find any information about weisgauff machines on the forum. German cars. Judging by the ratings and reviews, they are quite good.
Unsubscribe, owners! Share your impressions. :Search:

They give me the Zanussi PMM
She has a brush indicator lying around
According to the owner, it’s something with an optical sensor
Tell me, is this true?

I can’t figure out how to adjust the water hardness. According to the table from the manual, the water hardness setting data is given only in German degrees (’DH) and in mmol/l, and in accordance with these values, the softening level on the regulator is set (from H1 to H6). Our values ​​in (G) are not there. I used a calculator of these values, it turned out that with our water hardness of 5F...

THE MESSAGE IS CONSTANTLY RECEIVED ON YOUR PHONE - DOOR CIOSE REMINDER. THE SMART APPLICATION IS CONNECTED. I DON’T UNDERSTAND WHAT’S THE MATTER. I WOULD BE GRATEFUL IF YOU CAN HELP WITH ADVICE.

They filled in the PMM, when starting up, water came in, but the drain was blocked. As a result, error E4 is displayed. The water was removed from the salt compartment with a hose and syringe. There is no visible water. The error is on. Apparently there is water in the pan.
Tell me how to drain the water from the pan?

I can’t remove the top tray for forks, knives, etc. because the large plastic piece is stuck behind the sprinkler arm. I can stick my hand in, I need to remove the rotating cap and then I can pull out the part. Question: How do you remove the cap? I tried it with my hand and it doesn’t feel right to the touch. Can use a screwdriver to pick it up

GOOD DAY. I HAVE THE SUCH PROBLEM, I DOUBT whether MY DISHWASHER RINSES THE DISHES GOOD. AND THIS IS WHAT I NOTICED, IF YOU PLACE AN UPVERTED GLASS AT THE END OF THE CYCLE WHEN YOU RINSE THERE IS CLOOKY WATER IN IT AFTER THE FINISH OF WASHING. AFTER THIS I RUN 2 ANOTHER QUICK CYCLES WITHOUT DETERGENT BUT THE WATER IS STILL CLOUDY. WHAT DOES THIS MEAN?
THE DISHWASHER IS CLEAN,, THE FILTER IS CLEAN...

Hello
This is a problem - water flows into the dishwasher, through a round thing, I don’t know what it’s for, maybe for drying, I’m attaching a photo.
After the cycle is completed, if you don’t turn off the water supply with the tap manually, it will slowly , water leaks in a small stream and accumulates in the dishwasher itself.
Video here: ObFPgbsxGCY

The low salt light is on when there is salt, tell me how to fix this?

Neff dishwasher error E15 and the faucet is blinking, I removed the bottom panel, water is dripping from here. What could this be, how can I fix it?

HELP PLEASE!!! PYRAMIDA nneed help. Built-in dishwasher PYRAMIDA DP 09

When connecting the drain, the installers forgot to remove the plug (that is, the drain was tightly closed)
when the drain pump started working, all the water was on the floor.
I found the problem, I opened the plug and started again when draining, all the water was on the floor
I removed the side cover and found the water...

I have a Mastercook ZBI-3646A dishwasher, which began to stop for some time after being turned on, and then all the diodes blink and start beeping. Accordingly, the water does not drain, there is a certain smell. After a few hours you can restart it and it will continue to work again, this continued for about a month. Now it won’t start, it makes clicking noises and then beeps. Where to dig, what...

Greetings. IKEA began to leak, the master named the price at 7,000 rubles, Moscow. He said that he used sealant there, sealed the holes, etc. Real price or a scam? I also took the module for repairs, the relay on the diagram was fried, another 3600 for that. Tell me, did you overpay a lot?

When the Kuppersberg GS 4502 was turned on for the first time, it began to take in water, then error E2 was rebooted and started, and now it showed error E5. I can’t understand the normal water pressure, what it needs, has anyone encountered this? I would be grateful for the information.

Good afternoon!
The question is: on the PMM the mode is 30 minutes. It washes until the end of the cycle and when there is already 1 minute left on the display (0 minutes), it waits and the time counter is set to 15 minutes and the PMM washes again. Those. It feels like the counter is being reset. PS: I’m not complaining about the quality of dishwashing