Hansa

Hello, the middle basket is rubbing against the two sides of the hansa dishwasher, tell me what to do?

Good afternoon, there is a problem with the hansa zim654h dishwasher
It fills up water, thinks, fills in water again - like this 3-4 times
Water starts overflowing over the front edge
Then it gives the error no water pressure
At the same time, the pressure is normal, nothing interferes with the drain
Ie. Logically, some sensor does not detect the pressure
Tell me - what exactly should I look...

Good afternoon.
The problem was floating, one fine day the machine finished the cycle, and when turned on again it got an error - overflow. I disassembled it, drained the water from the pan, the float fell into place, there were no problems for a year. Then the problem began to appear more often, I did not disassemble it, I simply tilted the PMM, water flowed out of the pan and the machine worked...

Hello. The spring of the dispenser cover flew out. Help me insert. Thank you.

Good day! I turn it on, select the mode - it draws water, the time is counting down but DOES NOT WASH :(, goes through a full cycle, drains the water and beeps that everything has been washed! This happened 2 weeks ago, then it started working on its own. I thought it was some kind of glitch now he doesn’t want to wash anymore and that’s it! Please help advice from the Guru of this forum! Thank...

Good afternoon, the problem is that 5 volts disappear intermittently from the motherboard - that is, no, because of this the dishwasher constantly turns off and on, how to solve the problem, there is fee donor

Good afternoon, mmm hansa zim, after filling the water it buzzes and there is no action. After the reset, you turn on the program, it drains, then it dials, the relay is triggered, it buzzes and that’s all.

Help please.
PMM thinks for a long time before starting to wash the dishes.
Input data. The PMM draws in water quickly and drains just as quickly.
I disassembled the PMM, on the motor that supplies water to the nozzles (where the heating element is still located), everything is fine - there is no dirt, nothing rubs or catches. I also blew out the pressure tube (it was free of contamination)....

Hello! There is a PMM, in certain washing modes an error appears (the quick wash and 90 minutes indicators flash quickly), according to the manual it does not heat up to the required temperature. As far as I understand, condensation drying does not work, since the error appears only at the end of the program. Accordingly, when opening the PMM, there is no steam, but the dishes are all warm (not...

When you turn on the Hansa 615n PMM, all indicators blink alternately from left to right

Citizens, I ask for advice, because calling a technician to take a look costs a fee, and the installer is only available in a week. No patience. :muza: We opened the box, removed the shipping screw at the top of the door, but the door itself does not fit tightly. And it seems like it should snap into place? Or do I not understand what? And that white thing in the photo is the lock? Or is this...

Good time. I set it to wash for an hour.. it works.. at the end of the wash the error e8 beeps and lights up..
water flows in. the heating element heats up.. the water is drained. The dishes remain poorly washed. supplied voltage 220v. to the selector valve. It spins, closing and opening the micro switch, which is also in good working order.
help with advice.

Hello.
I purchased this miracle washer not long ago, the first time I turned it on, the salt light came on.
I filled in almost 1.5 kg and immediately filled it with water as per the instructions, the salt light went out. But during the first wash, the light came on again. After I took out the dishes and unscrewed the lid of the tank, I saw that the tank was almost empty.
The remains of water and...

Hello! Please tell me - the Hansa 416 dishwasher takes in water, but does not go into washing mode (in any dirty modes) - what is the reason???

Good afternoon!
Dishwasher: Hansa ZWM 627 IH
I encountered the following problem: the machine washed soap on a 2-hour cycle. After about 15 minutes it beeped and stopped washing. And after a while I started going through modes (it looked like these were test modes), at the end of which there was an F1 error. The machine does not respond to any buttons.
After turning it off and on - the same...

PMM Hansa ZWN601IEH does not wash dishes well due to insufficient water level in the chamber; it does not respond to pressure switch adjustments and even when the pressure switch is turned off, the same level rises

Good afternoon!
Hansa PPM, the washing cycle was interrupted by opening the door for 5 hours. After closing the door it did not work (it hummed, but did not draw water). There are no leaks, the pan is dry. Leakage sensor (connected to the foam float) - working. The electronic aquastop broke (checked with a voltmeter), replaced it with a new hose with an aquastop. The first start - I took in water...

Hi all. This problem happened. The dishwasher stopped heating and drying. I checked the filter too. What are the options - what else to see? It doesn’t give any errors. It washes cold and for a very long time (it feels like twice as much). I want to fix it myself - I have the hands. But we need to direct what to do, what to replace.

The upper sprinkler above the spoon tray on the Hansa PMM flies off.

We bought a new Hansa ZWM 428 WEH PMM, connected it, opened the water tap and water began to fill the PMM. They turned off the water, disconnected it from the network, opened the water again, and it continued to fill. In this case, the water does not drain, it simply rises from the bottom of the PMM. What is the reason? What to do? Change?

My hansa at the dacha before winter everything was turned off. drained the water. In the spring we started everything up normally and started working in the set mode
then the IVF mode immediately switches. loud beep and then stops. In the instructions, this mode means overflow
of water and water flows out from under the bottom. Can anyone tell me what’s wrong with it.

When rinsing or washing at 70 degrees, it creaks and rings, similar to the ringing of a tin, but it is cyclical, regardless of whether there are dishes or not and does not depend on the detergent. When stopping and switching modes i.e. when the water is refilled, the cold creaking disappears. I blame the bushings of the circulating pump.

Good afternoon, I’m asking for advice. In general, it was like this: I loaded the dishes, set them to wash for 1.5 hours, after about 20 minutes I found a puddle near the PSM, I opened the door and there was a full bottom of water. I turned off the PSM, immediately turned it on, after 3 seconds the “Glass” icon lights up and flashes, beeps, nothing works except the on/off button.

Hello everyone.
The Hansa ZWM 627IH dishwasher does not heat the water.
I did:
I checked the heating element with a resistance tester - ok.
I connected the pressure switch, which is near the heating element, to it tester and blew into it - ok.
The second pressure switch, which is screwed to the side wall below, blew into it with the tester - ok.
Now the interesting thing:
A sensor is installed on...