Hansa ZWM526 in modes when the PSM washes or rinses at 70 degrees, there is a terrible creaking or squealing

Hansa ZWM526 in modes when the PSM washes or rinses at 70 degrees, there is a terrible creaking or squealing ⇐ Hansa

1 post • Page 1 of 1

Evgeniy 1967

Hansa ZWM526 in modes when the PSM washes or rinses at 70 degrees, there is a terrible creaking or squealing

Quote

Post by Evgeniy 1967 » 06 May 2018, 18:46

When rinsing or washing at 70 degrees, it creaks and rings, similar to the ringing of a tin, but it is cyclical, regardless of whether there are dishes or not and does not depend on the detergent. When stopping and switching modes i.e. when the water is refilled, the cold creaking disappears. I blame the bushings of the circulating pump.

1525625176

Evgeniy 1967

When rinsing or washing at 70 degrees, it creaks and rings, similar to the ringing of a tin, but it is cyclical, regardless of whether there are dishes or not and does not depend on the detergent. When stopping and switching modes i.e. when the water is refilled, the cold creaking disappears. I blame the bushings of the circulating pump.

Post Reply Previous topic Next topic

1 post • Page 1 of 1

Quick Reply

Subject:

Username:

Change Text Case:

Smilies

View more smilies

This reply contains at least one attachment.

If you wish to attach one or more files enter the details below. You may also attach files by dragging and dropping them in the message box.

Maximum filesize per attachment: 15 MiB.

Filename:

File comment:

Filename	File comment	Size	Status

Similar Topics

Replies

Views

Last post

Hansa ZWM 627 IH stops washing and switches to different modes

Last post by mahanka « 18 Apr 2020, 04:17
Posted in Hansa
Replies: 1
by mahanka » 11 Apr 2020, 10:05 » in Hansa

First post

Good afternoon!
Dishwasher: Hansa ZWM 627 IH
I encountered the following problem: the machine washed soap on a 2-hour cycle. After about 15 minutes it beeped and stopped washing. And after a while I started going through modes (it looked like these were test modes), at the end of which there was an F1 error. The machine does not respond to any buttons.
After turning it off and on - the same...

Last post

Exactly, it was a matter of oxidation on the buttons. Where there are contacts, everything is fine. And from the side of the buttons themselves, it turned sour. The technician replaced all 4 buttons. They served for 6 years, I hope the new ones will last at least as long :)
This topic can be closed, thank you!

1 Replies

23109 Views

Last post by mahanka
18 Apr 2020, 04:17
PRIVILEG machine, rinses with cold water, does not dry

Last post by Natalia « 04 Oct 2014, 22:57
Posted in Other manufacturers

by Natalia » 04 Oct 2014, 22:57 » in Other manufacturers

:( Dishwasher Privilege, approximately 2004, from Germany, used, Molel 6200X, the entire cycle works fine, washes perfectly. During all cycles, the water heats up as expected. But it rinses with cold water. I think the type of drying is condensation with fan. The fan motor works, the fan spins, the drying indicator lights up as expected. There are no instructions or manuals accordingly. Could...

0 Replies

30161 Views

Last post by Natalia
04 Oct 2014, 22:57
Opening the door with a creaking and rattling spring

Last post by Spring « 16 Nov 2021, 15:19
Posted in Midea
Replies: 1
by TatyanaF » 16 Nov 2021, 05:42 » in Midea

First post

Good afternoon. The door began to open very hard and at the same time there was a grinding sound of a spring or something else. My husband took off the case, everything went away, loaded the machine and everything came back again. It seems to me that the door has stretched, i.e. While you are loading it, it takes on the load and something is stretched.

Last post

It’s clear! Keep monitoring! We will contact you! :muza:

1 Replies

10540 Views

Last post by Spring
16 Nov 2021, 15:19
At 70 degrees the faucet lights up

Last post by Fuchs « 24 Mar 2023, 19:34
Posted in Bosch
Replies: 12
by Sergey Egorov » 08 Oct 2017, 21:02 » in Bosch

First post

Hi all! In the 50 degree mode there are no problems, at 70 degrees the faucet works for about 40 minutes and the faucet lights up, the machine begins to make noise (apparently it’s trying to pump out water). So, before starting, I disassembled the machine, the pan was dry, I started the 70 degree program, about 40 minutes later it caught fire the faucet and the machine stopped working; upon a...

Last post

Tehnolog, handsome, got to the bottom of the problem, there is a special repair kit that seals this place, part number from Bosch Repair kit seal Bosch 12005744 white

12 Replies

34329 Views

Last post by Fuchs
24 Mar 2023, 19:34
SKS40e02 heats water only 45 degrees, higher - cold.

Last post by Thermostatic « 11 Apr 2022, 21:09
Posted in Bosch

by Thermostatic » 11 Apr 2022, 21:09 » in Bosch

SKS40e02 heats water only 45 degrees, higher - cold.
I have 4 positions (45, 50, 65, 70) degrees on my dishwasher. But I started heating it only at 45 degrees, I set it higher - the water was absolutely cold. What could it be!

0 Replies

4455 Views

Last post by Thermostatic
11 Apr 2022, 21:09

Return to “Hansa”