Electrolux esf 2410 does not heat water

Electrolux esf 2410 does not heat water ⇐ Electrolux

1 post • Page 1 of 1

Автор темы
amulets: Total posts: 1; Joined: 23.01.2022

Quote

Post by amulets » 23 Jan 2022, 18:51

Everything works, but does not heat the water, the heating element rings at 45 ohms. Please tell me where to dig

1642960295

amulets

Everything works, but does not heat the water, the heating element rings at 45 ohms. Please tell me where to dig

Post Reply Previous topic Next topic

1 post • Page 1 of 1

Quick Reply

Subject:

Username:

Change Text Case:

Smilies

View more smilies

This reply contains at least one attachment.

If you wish to attach one or more files enter the details below. You may also attach files by dragging and dropping them in the message box.

Maximum filesize per attachment: 15 MiB.

Filename:

File comment:

Filename	File comment	Size	Status

Similar Topics

Replies

Views

Last post

Electrolux does not heat water

Last post by dubalex « 28 Jun 2022, 21:02
Posted in Electrolux
Replies: 7
by chubarev1994 » 23 Jan 2022, 22:44 » in Electrolux

First post

Good day, the electrolux dishwasher does not heat the water, the power supply to the heating element is 51V, while replacing the heating element itself, the circulation pump, the temperature sensor, the flow distributor, and even the control module, but the power supply still does not heat

Last post

Good afternoon!
I have the same problem (36V on the heater).
Can you tell me if flashing/repairing the control board helped? Which board was repaired, the one that directly supplies voltage to the heater (in my case, it is installed on the rear wall at the very bottom)?

7 Replies

15960 Views

Last post by dubalex
28 Jun 2022, 21:02
Electrolux esf9552low does not heat water

Last post by Graphics « 15 Mar 2023, 19:10
Posted in Electrolux
Replies: 4
by psyhit » 13 Jul 2022, 08:54 » in Electrolux

First post

Hello everyone. The machine stopped heating the water, the heating element rang both in dry mode and in operating mode, temperature sensor, everything is ok, about 30V comes to the heating element, I looked at the errors in the service mode, it shows i64 i65, I couldn’t find the value anywhere. I’m sinning for the fee.

Last post

Good evening. how to check whether there are errors on the electrolux esf9552low dishwasher or not? Thank you.

4 Replies

10192 Views

Last post by Graphics
15 Mar 2023, 19:10
ESL94201L0 does not heat water

Last post by Mr.Cheese « 13 Feb 2017, 16:39
Posted in Electrolux
Replies: 1
by Yulia » 06 Feb 2017, 17:09 » in Electrolux

First post

Good afternoon After washing the dishes, a part was found at the bottom of the PMM (photo attached), we examined all the dishes, such a part could not have fallen off from anywhere! Accordingly, the part is from PMM! What could it be?? Or maybe immediately, or maybe after a couple of days (they didn’t pay attention right away), the machine stopped heating the water and drying! The filters have...

Last post

The PMM always has some water left at the bottom, which is technologically conceived. Because Dishwashers most often use the condensation type of drying (using a temperature difference), then poor water heating will immediately affect the drying too, therefore it is necessary to solve the problem, first of all, of poor heating. Check the filters and drain carefully. If there is too much water at...

1 Replies

23741 Views

Last post by Mr.Cheese
13 Feb 2017, 16:39
Smv50m50ru /74 does not heat water

Last post by Chinese « 17 Sep 2021, 15:56
Posted in Bosch

by Chinese » 17 Sep 2021, 15:56 » in Bosch

Good afternoon. The situation is this: the Bosch smv50m50ru car, after replacing the motor (actuator) for switching the water flow, stopped heating. Everything seems to have been assembled correctly. It works, the cycles go through, but the time doesn’t match now, instead of 30 minutes of quick washing, it washes for over an hour. And only cold water. Ten checked, 20 ohms. What could be the...

0 Replies

5350 Views

Last post by Chinese
17 Sep 2021, 15:56
doesn't heat water

Last post by Mr.Cheese « 21 Mar 2017, 16:14
Posted in Siemens
Replies: 1
by Vitana » 20 Mar 2017, 20:08 » in Siemens

First post

The machine stopped heating the water; the heater rings; the thermal sensors are checked; one is 100 ohms when heated; the other is open; when heated, it turns on at 35 and 60 degrees. What :sorry: could it be?

Last post

Try cleaning using these instructions

1 Replies

37746 Views

Last post by Mr.Cheese
21 Mar 2017, 16:14

Return to “Electrolux”