Bosch - Page 4

PMM Bosh SKS60E18RU, manufactured in 2012, during operation the heating element with the pump was changed three years ago, it started randomly displaying error E01 - regardless of the program, at a random moment in the cycle an error pops up, it may work for 5 minutes, maybe 15, but the result is clear - E01
I cleaned the machine - I poured boiling water over the drain, then took it apart,...

DV! We bought a Bosch dishwasher less than a month ago. During this time, after the washing cycle is completed and the water is completely drained, water is drawn back into the pan through the hole on the side below. We applied under warranty, but since there is no warranty service in our city, the master tried to consult remotely and rendered a verdict that most likely this was not a warranty...

PMM SMS50E02EU/02.
The machine worked without problems, but while fixing the leak, it was discovered that the heat exchanger was only a third full.
Water enters the machine, is heated and drained.
The valve at the bottom right is loud (it has been working for so long, maybe always)
What could be the reason?

Has anyone noticed that the dishwasher uses more water per cycle than indicated in the specifications?! We bought a Bosch spv66mx20r, used it 5 times, then out of curiosity I decided to check how much water it spends. I looked at the meter, turned on the dishwasher for an hour, didn’t use any more water during that time and it came out to 35 liters, compared to the stated 10! I checked this 2...

It drips from the white plastic case to which the motor of the flow distribution mechanism is attached, sometimes it drips onto the motor itself. During a wash cycle, about 50-100 grams leak. It looks like the reason is the seal at the wheel axle with holes for flow distribution? Please tell me how to solve the problem: should I order the entire mechanism assembled or are there other ways to deal...

After the end of the washing cycle, the tray is clean and without water. After some time - half an hour to an hour - it is noticeable that water is entering the pan. Three hours later - the pan is full. The problem appeared recently. Backflow from the hose is unlikely, everything is connected properly, and the check valve is normal. Is it possible to enter through the inlet hose? Or are there...

Good people. Tell me, I’ll resuscitate PMM at home. Machine SKS50E12RU/05 ... Works through the program, and upon completion freezes. I think the machine is hanging at the drying stage. I’m not much of a repairman, but apparently there is a problem either in the temperature sensor or in the brain, because throughout the entire hang time the heating element is burning. Tell me where this sensor is...

Comrades, good afternoon!
Does anyone have a diagram or photo of connecting the wires to the control module of the specified device. Bosch responds to inquiries: contact an official service center. And I’ve already said enough, that’s enough.

:swim: machine 46A53 started the washer..during operation the water was turned off. The machine drained and stood there humming...now it won’t start, it’s buzzing, it won’t fill up with water, I forced water in, it WASHES, it warms up for about 15 minutes * the water doesn’t drain..??How to restart or is something wrong?I would be very grateful for your advice

After turning on the power, the drain pump immediately starts for 30 seconds (I don’t remember if it was like this before), then the pump turns off and the washing motor starts for 30 seconds. Then the PMM turns off. During all this time, water does not flow through the fill valve. The water poured into the PMM with a ladle is quickly drained when the pump is running, new water does not enter.

I...

There is no 1/2 button in your bosch dishwasher? How to start mode 1/2?

There was a power surge throughout the entire entrance. After all the markings worked, they called the housing and communal services electrical service. They measured the grounding and all showed 400 Volts. They were doing something in the shields. The sockets worked, but the dishwasher did not. Could the board burn out if it was plugged into the socket but did not work? The voltage surge made a...

Hello everybody! I would like to describe my experience of repairing a Bosch dishwasher with my own hands, maybe it will be useful to someone. After 3 years of operation, the dishwasher produced strange variations of indicator lights and wet dishes at the end of the wash. Because Having never been in a dishwasher, it was decided to call a professional. The master arrived very quickly and with the...

Like all Boshes, mine has a leak, but I couldn’t completely solve it; the homemade silicone gasket leaks during breaks for more than a week. This time I decided to take it apart and wipe it with a rag, but apparently the urine got to my head and I climbed from the right side, although it was possible from the facade, in short, I pulled the board off, after assembly it stopped heating, no errors....

There is a Bosch SMV40E50RU/54 dishwasher. Stopped heating water. I took it apart and looked at what was there. It turned out to be a breakdown on the heating element. I disassembled the pump itself using the article swen( ). I would like to add that it is difficult to remove insulation from the tracks, so you will have to tinker with this. I connected the leads and checked with a multimeter №1...

Hello!
The BOSCH SPV40E30RU/07 PPM has started to show off.
It doesn’t work as expected in all modes. Soon after the start it starts beeping, ends without throwing away the tablet, the end and faucet are on. During the last attempts, water began to flow out, apparently from the door. Related: reset doesn’t work. Help me please!

The bosh sps5452 has been serving us faithfully for 20 years now and finally, at the end of 20 (apparently there was a coronavirus involved) it started leaking. Coincidence? I don’t think :-D the rubber gasket is leaking, which is located in the place where the drain hose and the dishwasher are attached. Model bosh sps5452 Has anyone come across this and knows where I can order gaskets for this...

Hello, please tell me what the error is and how to fix it. Thank you in advance.

Comrades, please tell me who has encountered error E05 (the actuator is constantly working, the triac of the actuator motor is faulty) the problem is in the control module. Does anyone know what burned out?

help! the dishwasher fills and immediately throws out water! what should I do?

After the washing process there is strong condensation on the walls, but the dishes are clean and dry. What is the reason?

The Bosch 60 cm built-in dishwasher displays error E27 after a power surge and does not work. I’m doing a reset. Everything is in vain. Now the tension is normal. There doesn’t seem to be anything burned out on the board. What else to do? The filters have been cleaned.

The heating element burned out, the old pump is not for sale. I bought a new one, but got confused and took it without wiring (it’s on sale right away with wires for connecting to old models, so as not to bother) I found the chips, there’s also a photo of how to connect the wires, but there seems to be a resistance to the twist, and I don’t know what kind is needed. Maybe someone knows, thanks in...

The hostess complained about the poor quality of dishwashing.
A test cycle was carried out on the intensive washing 70 deg mode. Before starting, the indicator showed something like 125 minutes.
The pre-wash stage seemed to go well: the machine was vigorously splashing from all the impellers, the water temperature was close to 50 degrees.
The main stage / the intermediate wash was strange:...

Good afternoon!
I have lost one fastening for the grille of the lower basket of the Bosch SRV43M13EU/38 dishwasher (I have attached a photo).
I have no idea where I can buy it or how to replace it? None of the online stores or official dealers have this in stock.
Please advise.
IMG_4882.JPG IMG_8125.JPG

The track on the heating element has burned out. I cleaned small sections of the track, applied copper by galvanizing, tinned and soldered the jumper.
As a result, the PMM does not turn on. I hear a few clicks and that’s it. The screen doesn’t light up either. The situation changes if I just turn off the power to the pump - then I get error e20, which is logical.
Where to dig, how to diagnose?

Bosh 33A13/14 does not heat water, the cycle does not complete
The resistance of the heating element corresponds to the power (it has not applied direct voltage yet), the temperature sensor changes resistance when heated from 50 to 15 kOhm.
In the case with A water presence sensor is embedded with a heating element; water presses through a rubber membrane on the piston, and it presses on the...

I read a forum with this error
There is no water in the dishwasher
The first time the error appears is after about 40-50 minutes of washing. I immediately restart and the error appears after 1 minute. I restart again and the wash goes through without errors, that is, the wash goes through without errors only after 3-4 restarts. I took out the flask with the filter, without it the same garbage....

My BOSCH SMU58M45EU/25 machine began to behave badly :(
When plugged in, without pressing the power button, it turns on spontaneously. Then self-testing begins, with characteristic sounds of relays and motors. Display At the same time, the LEDs and seven-segment lights blink, pressing the buttons does not change anything. After a short time, up to 30 seconds, the display and indicators go out,...

About 4 minutes after the start of operation, one heating element relay clicks (right in the photo).
The second (left) relay does not work because... no voltage is applied to it. Therefore, the heating element naturally does not heat.
The first relay turns off after about 1 minute, all the LEDs on the front panel blink, and only the first relay turns on again, then turns off, and everything...

The Bosch SPV 40E10RU dishwasher, in use for about 4 years, began to display a blinking tap error and a lit End indicator. It gives an error after drying, I took it apart, the pan is dry and there are no signs of leakage, I also cleaned the heat exchanger, but it didn’t help, what could be the problem?

Greetings. PPM has been in operation for more than 10 years. Lately, problems have emerged: it doesn’t wash dishes well, stale powder remains in the dispenser, sometimes it washes with cold water. If it sits for several days, it washes normally the first time, but not well the second and subsequent times. There are no accidents, different washing cycles are completed correctly. There is no water...

Hello. The situation is this: the machine was washing dishes, then it beeped as if it had been washed, they opened the tap on the panel, the tap was on, I tried to reset the start button for 3 seconds - there was no reaction, I tried again - nothing, but the drain pump was constantly working every minute - one and a half, not a single button responded to pressing, I had to turn off the power....

I have been using a Bosch CRI 45M EV dishwasher for 12 years now. No complaints during this time, but I encountered the problem that jets of water come out, but do not reach the dishes and do not spin the rocker arms, but simply give fountains of 3 centimeters, while the water does not heat up and the program restarts on its own at the moment when it is necessary to start heating the water . When...

Hello. Bosh SPS25FW13R/01 was purchased to replace the old Siemens PM. During the warranty period, this machine’s faucet icon began to light up periodically. It caught fire around the time of drying. Under warranty, they replaced the water inlet sensor (on the right) and the circulation pump (!!!). The problem did not disappear, on the contrary, it began to appear almost every time I wash it....

Good afternoon
We had some trouble. The flexible hose of the mixer broke. There was quite a lot of water in the kitchen. We fixed the leak, collected the water, dried the floor and began connecting the household appliances back. We discovered that the PMM does not respond to buttons at all. I rolled it out of the headset and saw that water had filled the pan. Accordingly, the control board is...

after turning on the dishwasher program, water fills in, then something clicks and it starts to squeak, drains water and at the same time fills in water. At the same time, there are no leaks in the dry pan. All filters are clean. At the end the faucet indicator lights up.

Bosch SMV59T00EU stopped heating water. It gives error E09. The dishwasher is 10 years old. I read the threads on this wonderful forum and found how people fix it. I’ll tell you about my repair :roll:
doesn’t heat the water
Here a friend described . Looking ahead, I will say that there is no need to cut or break anything - everything is assembled and disassembled. In general, this is not the...

Yesterday the dishwasher stopped working, the filters were clogged, I accidentally pulled out this part, how do I put it back??? I’ve been poking around and can’t figure it out *x)

Tell me, is the Ten pump of these models SPV40E30RU/08
SMV47L00RU/09
interchangeable?

The machine stopped supplying water, error E15 and the red no water supply symbol came on. At the same time, everywhere in the pan is dry, like in Sakhar, no leaks were found. As I was told in a store where they sell spare parts, 220 V should be supplied to the aquastop valve. I measured it with a tester, when I turn on the car, 220 V does not come to the valve. I disconnected the chip and wires...

After washing the dishes have a white coating. please tell me what is the reason? salt is the finish.

Hello everyone
When we moved to a new apartment, the former residents left behind a kitchen, including a built-in Bosh machine. It’s been standing for a long time, it’s been used before, it’s connected, it even lights up when you turn it on. I myself had never even thought about buying it before, but here I’m using it) I myself am more into computers and other electronics, my maximum is to...

When turned on for washing, it initially shows 2.30 - 3.10 remaining time. The process crashes and actually washes for an hour or 1.5 hours. The dishes are not washed well. changed tablets, salt, etc. without result. The dishwasher is 9 years old. Apparently there is a software glitch. Or are there options?

:hello: :
Hello. The machine worked great until today. It washes the dishes, BUT it stopped signaling the end of the 📡 cycle and does not turn off itself. I have to force it to turn off. What it is? Need a master?

Good day to all! Please tell me, maybe someone has had this problem, I have a Bosch dishwasher, lately something has started to go wrong in it, can someone tell me what it is, I’ll write down the problem:
When you turn on the machine and select a mode, it starts to wash, then the screen goes out, after some time it starts working again, and this can continue indefinitely, maybe someone knows what...

I removed the SMV69T70RU/70 pan, and this was the only stop left. I can’t find a diagram of how it stood correctly and what it supported - please help with advice or a picture, please)

The filter is clean. I restarted the program. Please advise what to do?

Hello everyone.

The Bosch SPV63M50/RU23 dishwasher, when I try to turn it on with the Power button, beeps twice and does not turn on. There is no indication on the screen.
This has happened before. You leave it for some indefinite time, check that it is working. Then, after a few times, it happens again.
Now it has been beeping all day.
The machine is built-in. There is no water inside. There is...

Help, the faucet caught fire.
The water to the valve is 2-3 kg/cm2
The valve on the coil shows 3.8 kOhm
After manipulations of turning over and checking the valve, it started up once and fell out again Same error.

I couldn’t find any clear hints on the Internet about this machine.