Electrolux - Page 2

During washing there was a burning smell. It turned out that the connector from the sink to the board had melted (the “mother” chip on the board was also a little). What could be the reason? The module was changed 3 years ago. The car wash is 10 years old. One specialist advises the heating element to check the capacitor as well. What other reason could there be? What else needs to be checked?

Hello, dear comrades.
The dishwasher does not plow.
It constantly tries to drain the water at the start of the washing cycle.
The pump (from a stray pipe) supplies water, I tried it by connecting the wires directly.
Everything rang, the board is intact, there are no smudges or any scorched places.
Error R20
When you turn on the wash, the water drain is triggered, and so on three times, after...

Can anyone tell me what to do about this or how to adjust it? After 6 years of operation, the door began to leak in the upper part (from the control panel side). In fact, when I pulled out the dishwasher, I discovered that the door seemed to be warped and moisture began to seep out in the upper right part of the door due to a loose fit during operation.

Electrolux esf 43020 the aqua stop is triggered.
I removed the side cover, started the washer, during observation I discovered that water began to drip from two hoses into the pan and then the aqua stop triggered.
I assume that water entered the chamber in a larger volume what is necessary and how to pour water through two hoses.
QUESTION: Which part is faulty???
Presostat (water level sensor)...

Electrolux esf 43020 aquastop is activated, it flows from two hoses into the sump, what could be the reason???

The ten on the Electrolux PMM stopped working. After ringing, it turned out that one of the two thermal fuses installed on it had blown. And here’s the catch: the services only replace the whole thing, and for no less than 7,000 rubles. And then you need to change a small round thermal plate made of thin metal. Can you tell me how to solve the problem or order this miracle of technology?

The door on the dishwasher dropped slightly to the right. How can I fix this?

Hello! There is a problem with the dishwasher, as soon as I plug the plug into the socket, water immediately starts pouring in.

Hello! There is a problem with the dishwasher, as soon as I plug the plug into the socket, water immediately starts pouring in.

Hello, does anyone have a template lying around for a PMM Electrolux 45 cm for a kitchen façade?

Hello. Dishwasher with airdry function. Opens the door slightly 20-30 minutes before the end. And accordingly leaves a white coating. Has anyone encountered this problem?

Hello! I stopped heating the water. The heating element seems to ring (25.5), but the contacts come to some kind of ceramic insulators or something else and there is 0 resistance on the contacts. Is this how it should be?

The dishwasher doesn’t rinse, it’s like there’s scale on the dishes

The first and subsequent launches at the end of any program there are loud clicks for about 5-10 minutes... anyone else has this.... what do we do???

Good afternoon, there is a problem with the dishwasher door hinges. The door opens very tightly, the hinges are very movable, one rivet almost flew out. There is also metal-on-metal friction, so much damage ((. Is it possible to restore (change the rivet) or still buy new hinges? Thank you image.jpg

Hello!
Is there a way to change the default program number (P4) to some other one.
Thank you!

Good day everyone, I have a PMM Electrolux esl48900r.
The time projection on the floor has stopped working...
What could be the reason, maybe someone can tell me?

Good afternoon, dear ones. Help me choose an analogue to replace the pressure switch PM Electrolux 37640504 132516204

Hello.

New dishwasher model ESL94200LO from ELECTROLUX.
When turned on, it is not possible to change the washing modes. It turns on in ECO mode.
My wife and I read the manual together. Are we doing something wrong? Or maybe the button doesn’t work? Repair?

- a short example of work

Hi all. Machine Zanussi ZDS-200, more than 10 years old.

On the third day the exhaust pump began to malfunction, I, on the advice of the specialists, did not wait, but immediately bought a new one and replaced it. When I changed it, I put the machine on its back.

After this, the following syndrome appeared: it takes in water, but when it’s supposed to turn on the circulation and start...

Hello. There is a problem with the PMM: when you turn on the program, it constantly drains water. The “master” has arrived. Everything was inspected and everything was in order. It was decided that the problem was due to low water pressure. Time passed, the pressure increased, the problem remained. I called the “master” again, this time a different one. He said that there was a problem with the...

Hello! I bought a dishwasher model 94510 and it came with three capsules of Fairy detergent. When the machine was running, the smell from Fairy could be felt throughout half the apartment (it smelled until the door was opened at the end of the wash). After replacing the capsules with Finish tablets, the smell became much less, but it is still noticeable. Does your machine smell like detergent...

Electrolux esl95321lo dishwasher does not heat. Where to begin?

The machine care function indicator requires cleaning the inner chamber on which program to wash; I only show the washing time

Greetings to all. A couple of months ago, the Welling YXW40-2D circulation motor on an Electrolux 2300 OK dishwasher jammed. A small amount of water got onto the bearing due to wear out of the rubber bands or something. In our city (Murmansk) there are no normal craftsmen, only one name. All service centers and others immediately sell a new engine, which costs about 6,000-7,000 thousand rubles. I...

I inherited an Electrolux BW 545 machine. I had never dealt with dishwashers before.

Everything inside was covered with plaque, so for the first time I used a cleaning product, it didn’t help much.

I read on the internet that you also need salt. There are no instructions. I found something in Swedish, fiddled with the translation, but it didn’t say anything about salt. There is a compartment...

why does the door open less than 10 cm when air dry?

Good afternoon.
Electric luxury esf 45010s does not drain.
If you apply voltage to the motor, then everything works. What could be the problem? Why doesn’t voltage automatically flow to it when needed?

Doesn’t heat the water and doesn’t dry.........
where to start?
Thank you

Good evening. When you start the machine, all the indicators begin to flash quickly and the machine does not start. No error code is displayed. what could it be?

Help. The problem is this. The heating does not turn on as expected. The whole pressure switch is new. The flow sensor is new. PMM works without problems but there is no heating. The heating turns on if, after 5 minutes of the cycle, you turn it off and turn it on with the button. During operation, the flow sensor does not rotate and does not change the flow between the blades. The second...

Hello.
The question is the following. PMM Electrolux ESL94300LA.
Yesterday I washed dishes in an intensive wash. Without waiting for it to finish, he opened the door. I saw that the washing was not completed (there was a drying period), I closed it. She finished drying the dishes. Everything is ok.
Today, when you turn on the dishwasher, it does not switch to another mode. That is, I turn it on,...

Hi all! Electrolux dishwasher manufactured in 2015. I launched the program, after an hour of operation, water flowed from under the machine, the plugs in the apartment were knocked out, and the machine turned off. All at the same time. I called the technician and all indications were that the control module had died. QUESTION - is it worth changing the module?, the master says the modules can be...

Hello, has anyone encountered such a problem. Foam is pouring out of the machine. I don’t know what to do, we’ve only been using it for 10 months.

Good afternoon...maybe off topic...please tell me...
First PMM in my life and at the first start, when I poured salt into the compartment, I forgot to pour a liter of water there (as I later read in the instructions)... I started the car without water in the compartment.. the question is, is there a chance that the salt has already stuck together there? WHAT to do?
Second question: What in the...

Hello! I have a PMM Electrolux, the problem is that water does not flow into the machine. When you turn on the machine, the drain pump constantly runs. There are no leaks, everything rang, everything is normal. What could be the reason, please tell me.

The machine is 7 years old, the pipe was torn, they sealed it, now it’s completely fallen apart, I’m in St. Petersburg, delivery from Moscow, can anyone tell me what could replace it? art 1119165007

Hello everyone. The Electrolux ESF 2450 W device worked properly for more than 5 years. The water is good, northern, Murmansk region. But for the last couple of days, this situation has been happening: you start it (no matter what program), after working for a while, it turns off. This can be treated by taking it out of its normal place and bending it forward. Then it turns on and works. If you...

Dishwasher Electrolux esl 45010 (model 2007), suddenly started beeping, beeping 3 times, a break of 3-4 seconds and again.. and so on endlessly (((I called the technician.. on the first visit I cleaned the filter, took 500 rubles and left.. .half an hour later it beeped again...the second time he came, he disassembled and diagnosed the death of the filling hose with an aquastop, which costs 4,500...

Good afternoon.
Experience in repairing dishwashers - 0.

I replaced the drain pump in the PMM (the volute broke). In the process, I removed the fastener with two tubes at the base of the cochlea. The tubes didn’t seem to be inserted anywhere. Perhaps it was installed incorrectly. To be honest, I can’t even understand their purpose. In the photo, the fasteners with tubes are detached for...

When turned on, the dishwasher produces 4 light and sound signals. What kind of malfunction is this?

Dishwasher 505052 Electrolux displays error C7.
Tell me who knows what this error means.

Good afternoon I have an Electrolux, it’s 8 years old (I know it’s an old lady), I start the program, it starts washing and goes out completely, stops for 3 seconds then starts back up, during the cycle it can lose consciousness 6 times :) then it finishes its work. Is it over, or is it possible to prolong the patient’s life?

Dishwashers Electrolux ESL 47710 R
The machine is about five years old. During long programs, sometimes but not regularly it shows the 20th error approximately in the middle of the wash, after turning it off and on it brings it almost to the end, but again SOMETIMES but NOT ALWAYS (including on a 30-minute short program) the 20th one pops up error. Sometimes the entire wash goes through without...

Good afternoon After washing the dishes, a part was found at the bottom of the PMM (photo attached), we examined all the dishes, such a part could not have fallen off from anywhere! Accordingly, the part is from PMM! What could it be?? Or maybe immediately, or maybe after a couple of days (they didn’t pay attention right away), the machine stopped heating the water and drying! The filters have...

Hello, I bought a dishwasher model electrolux esl 5301lo, there are no instructions, I didn’t find any instructions on the Internet, this model is almost never found, this model is not on the Electrolux website either, tell me which instructions are suitable, thank you.

Good afternoon!

I started the dishwasher (ESL45010 911635220), after a while the RCD in the apartment panel tripped.
I turned the RCD back on, the dishwasher continued to work, but at the end of the wash the dishes were cold .
After this incident, the machine does not show any errors, but washes it with cold water as it goes.
I understand that the problem could be anything: heating element,...

It starts draining only when I wipe the optical sensor with a cotton swab...

Hello everyone,
My Electrolux ESL 47020 dishwasher broke down - it wouldn’t drain the water. I called the repairman, he ordered the drain pump - they replaced it and the machine began to drain. BUT! During the replacement process, the unfortunate master forgot how the pressure switch was connected and as soon as he did not connect the contacts to it, the machine did not fill the required volume...

Hello everybody. I came across this problem. I turned on the machine as usual at night. In the morning - the machine hums, as if it is pumping out water, the error code is displayed i10 - i.e. no water supply. Interestingly, when the PMM is turned off, it still buzzes. It stops only when disconnected from the network. The next time you turn it on, the same picture occurs. If you select a program...