Bosch SPS53E02RU error E15

Boris Kuznetsov · Post by **Boris Kuznetsov** » 28 Aug 2013, 12:18

Aqua-Stop has worked - error E15 is on - water has entered the pan.
How to remove it from there? I would like to see what’s in there.
How can it be pulled out or do I need to disassemble the car?
I have not found adequate instructions for disassembling the car anywhere.
If you disassemble, then please order - what to remove after what.
Thank you.

Michael · Post by **Michael** » 20 Apr 2015, 18:33

Kolkot:There are generally two reasons for water getting into the pan. The first is through the pump seal, and the second is when the water level in the car is exceeded. And excess water is poured in if the pressure sensor fails, or a small container of complex shape, screwed at the level of the tray outside the tank and connected by a tube to the pressure sensor, is clogged with dirt and grease. Water poured into the machine through a hole in the wall enters this container and compresses the air, which causes the pressure sensor to close the inlet valve and turn off the water in time. And if the valve does not close in a timely manner, water begins to flow into the pan through the pipe in the very container that compresses the air. As a rule, in this case the drain pump works, but if it does not work or cannot cope, a flood is guaranteed. The repair consists of cleaning that very container, which is theoretically possible even without disassembling the machine; just find the required hole under the filter and use available means to suck out the grease and dirt.

nIs there any way to clean the outside of this thing?
I have a built-in one, I just pulled it out from under the countertop and shook it. Water poured out from the bottom right (if you look at the front of the dishwasher). I didn’t take it apart right away, but if some of it spilled out, it means there’s still some there. I’d like to clean everything up.
And so - I turned on the power. It worked, now I started washing for 15 minutes. But I would like to forget about such removals for another couple of years.

Technology · Post by **Technology** » 29 Apr 2015, 19:27

For those who have a built-in PMM: this method helped me - I took out the baskets and hit the bottom of the machine with my fist from the inside. Everything worked.

Kostya · Post by **Kostya** » 30 Apr 2015, 00:21

Thanks for the advice. It really helped. The tap and E015 were on and wouldn’t turn off. I pulled it out, tilted it forward, shook it, put it back, turned it on and it worked!!!

Guest · Post by **Guest** » 13 May 2015, 03:13

Thank you

novel · Post by **novel** » 17 May 2015, 18:37

really helped

Marina · Post by **Marina** » 29 May 2015, 04:00

Hurray, thanks, everything worked for me!

Gennady · Post by **Gennady** » 09 Jul 2015, 08:07

Machine SPV53E02RU At some point in time, E 15 was displayed, but basically nothing is lit, it does not respond to any buttons, but the pumping pump works at regular intervals: - for about 45 seconds it works, for 30 seconds it turns off and then everything starts again. The Start/RESET button (Like "restarting the program" doesn’t work either) What should I do???

Post by **ALEXANDER555** » 19 Jul 2015, 13:40

THIS IS THE FIRST TIME IN MY LIFE I’M WRITING A REVIEW! BECAUSE THIS PROBLEM BLOWED MY BRAIN AND BROUGHT A LOT OF PLEASANT SENSATIONS. ALL OF THE ABOVE DIDN’T SAVE...E-15 CONTINUED TO BURN ON THE BOARD, AND THE PUMP ALWAYS, AT SMALL PERIODICITY, TRIED TO PUMP OUT THE NON-EXISTENT WATER. AT THE WORKSHOP IN OREKHOVO-ZUEVO THE BOSCH WAS EVEN REFUSED TO LOOK, AND AT THE DEALER IN MOSCOW THEY SNORTED AND SAID THAT JUST THE ARRIVAL OF A WORKSHOP WILL COST 3500 RUBLES... CONTACT WHERE YOU PURCHASED AND Hung Up... GENERALLY DROPPED TO THAT THE PIECE IS PECULIAR, AND THE WARRANTY IT ENDED LITERALLY 5 DAYS HOW! AND THE DECISION WAS MADE TO DISASSEMBLE IT AND LOOK AT AS MUCH AS POSSIBLE FOR AN Amateur. THE PROBLEM WAS IN THE FLOAT, WHICH IS MADE FROM FOAM AND STANDS AT THE VERY BOTTOM OF THE CAR, BUT TO GET TO IT YOU NEED DISASSEMBLE ALMOST EVERYTHING AND REMOVE THE TRAY. IN PRINCIPLE, NOTHING COMPLEX, BUT IT’S BETTER TO DO IT
TWO... THERE IS NOT A SINGLE BOLT ALL BY THE POKE METHOD. IN MY CASE THE PROBLEM TURN OUT TO BE BANAL... A MOUSE MANAGED TO EAT HALF OF THE FLOAT! HE BENT DOWN AND PRESSED THE SENSORS TO THE LEAKS AND ACCORDINGLY THE AUTO STOP WORKED ...I REMOVED THE FLOAT AT ALL AND EVERYTHING WORKS EXCELLENT. LUCKY WE LIVE IN OUR OWN HOUSE AND THE PROBLEM OF LEAKING DOESN’T ARE PARALLY WORRIED. I HOPE THAT MY MESSAGE WILL HELP AT LEAST SOMEONE...

Miga4 · Post by **Miga4** » 19 Jul 2015, 19:19

Thanks a lot!!! It really helped.
Error e15 was on, no matter what I did. I disconnected from the network and again the error occurred. The dishwasher is built-in and it was impossible to remove it. I just twisted the legs, the machine looked like it was in a canopy, shook it and everything was ok. The error is gone.

Guest · Post by **Guest** » 29 Jul 2015, 22:24

Hello guys. I read the forum

and completely understood that something was sticking there, or rather the foam float and the leakage sensor was triggered. Therefore, opening the lid and taking out the lower basket, I tapped it around with my palm, not too hard, and everything worked!

guest · Post by **guest** » 08 Aug 2015, 21:28

After using the dishwasher gel, foam, water, and eventually the faucet and E15 flooded. THANK YOU for the tip with the tilts, it helped. Siemens machine T090-007

Olga1 · Post by **Olga1** » 12 Aug 2015, 18:57

I had this error several times, which was accompanied by foam leaking out on the sides of the door. Then this error remained on for several hours and the pump worked periodically. After drying, the error disappeared. The PMM did not pump because it was built-in and required dismantling. The serviceman called to help first of all asked - what detergent do you use? I showed the noname gel. He said that you should use only finish calgonite powder, because it does not create a lot of foam. And all sorts of gels form abundant foam, which pours out through the door under pressure. Or use these gels in a very small dosage, but then the quality of washing is questionable.

guest · Post by **guest** » 16 Aug 2015, 16:23

Thank you! And this advice helped us today!!!

M.Sergey · Post by **M.Sergey** » 21 Aug 2015, 07:15

Good day!
I had a similar situation. The reason turned out to be a leaking gasket between the "tank" and the plastic container where the drain pump is installed. Tightening the four screws that secure the tank did not help. I had to disassemble it (not very difficult, the pan is attached with latches, but it can’t be done alone), wash it and put it on car sealant - the leak disappeared. By the way, you can only drain the water from the container where the float floats without removing the bottom by tilting the machine on its side - this is extremely inconvenient, especially since any leaking liquid accumulates there, and there is nowhere for it to evaporate.

Alexei · Post by **Alexei** » 25 Aug 2015, 00:30

The method works 100%. Thanks for the advice!

Eugene · Post by **Eugene** » 30 Aug 2015, 20:46

The same error E 15 came on. I removed the filter. There wasn’t much water left in the drain hole. I collected the water with a sponge, it didn’t help. I checked the hoses, nothing. When I plugged it in, the pump runs for several minutes, the error remains.
The problem was solved tilting the machine forward by 40-45 degrees, with the machine plugged in and the lid closed. You could hear the remaining water, it was not clear where it was coming from, flowing into the drain hole. The error went out.

IgorRuss · Post by **IgorRuss** » 13 Sep 2015, 11:38

The dishwasher is built-in, a couple of specific slaps with your palm on the closed door cleared the error and brought it back to life! Ha ha! I didn’t even have to take it out or tilt it! Thanks to tube TVs and grandma’s ways of repairing them! It looks like everything is coming full circle, gentlemen!

Pavel · Post by **Pavel** » 20 Sep 2015, 12:04

The same thing worked for me!!!! Thanks for the advice!

Andrey B. · Post by **Andrey B.** » 04 Oct 2015, 16:55

Similar situation. Error E-15
I tilted the machine, a little water flowed out from below and everything was fine - the error went away, the machine turned on.
Thanks everyone for the advice!

Stas · Post by **Stas** » 16 Oct 2015, 08:26

Thanks people!!! Tilts helped

, my smart wife decided to wash the baking sheet and removed the top shelf

, and that’s it, I had hemorrhage for the whole evening until I came across how to treat it. Today I will tilt it

Rus · Post by **Rus** » 16 Oct 2015, 10:01

It helped a lot. I tilted it forward and the error disappeared. Now he’s rustling, washing the dishes.

Rus · Post by **Rus** » 16 Oct 2015, 10:02

It helped a lot. I tilted it forward and the error disappeared. Now he’s rustling, washing the dishes.

alexcccp · Post by **alexcccp** » 16 Oct 2015, 15:58

I confirm the built-in bosh
flooded with feri thought it would wash. foam flowed out of it.
then E15

I read that it should be tilted. unscrewing was treated by drying, it seems bullshit to me; vacuumed the drain hole 100% dry. I cut off the elva for about 15 minutes.

but the tilt solved the problem right away.

alexcccp · Post by **alexcccp** » 16 Oct 2015, 16:25

I will continue
analyzing my specific case caused by strong foaming!

on the left of my car there is some kind of expansion plastic tank (inside) and so
This is the second run of the 15 minute cycle does not remove the foam, put the soap in the machine so that the foam goes away.
I must say that I poured enough feri!

in short, about the barrel.
after all the runs the barrels are empty! but after error E15 it remained slightly filled with 300 milliliters of water. (it’s probably foaming there now)
It’s the tilt that will mix this water from the edge of the barrel drain! There is no point in drying such a quantity of water.

Guest · Post by **Guest** » 17 Oct 2015, 16:00

I tilted it 70 degrees forward without turning it off. Everything is working!!!!

Guest · Post by **Guest** » 25 Oct 2015, 16:57

How did you even have the brains to put fairies in the dishwasher? Just morons(((

Guest · Post by **Guest** » 07 Nov 2015, 09:21

Good afternoon, help, when you turn it on, the water supply indicator and rinse aid light up for a couple of seconds, then it turns off and does not respond to any commands

Guest · Post by **Guest** » 18 Nov 2015, 11:14

Error E 15. Symptoms: the water supply pump constantly turns on, the machine does not wash, E 15 is on. Do-it-yourself repair: Disconnect the machine from the power supply. Turn off the water supply tap. Unscrew the water supply hose from the water supply. Take out the filter mesh and rinse it. Blow out the water supply hose into the machine. The blowing method is the usual one: we blow into the hose with our mouth and suck out the water from there. 2 -3 times. Insert the mesh filter into the hose. Connect the hose to the water supply. Plug the machine into a power outlet.

Daughter · Post by **Daughter** » 29 Nov 2015, 09:13

I turned on the machine for the first time, worked for about 10 minutes and turned off, E15 was displayed, turned everything off. Now it won’t turn on, doesn’t respond to any buttons, and for some reason the pump is humming

Guest · Post by **Guest** » 11 Dec 2015, 15:07

Thanks for the advice. I just washed it with plenty of water, dried it and everything works again))))

Guest · Post by **Guest** » 19 Dec 2015, 07:23

Guys, it works! There was also an error e 15, I pulled it out and tilted it, a little water spilled out. Why did I turn it on? Hooray, it works! A little background. The lower rocker arm came off during operation.

Guest · Post by **Guest** » 22 Dec 2015, 16:40

Thanks a lot!! Indeed, after tilting, a little water flows out onto the floor, but the error disappears!!! and everything works as before)

SergWWI · Post by **SergWWI** » 24 Dec 2015, 16:31

Thank you, tilting helped!

Guest · Post by **Guest** » 26 Dec 2015, 07:37

Hello! Yesterday my child poured about 2 liters of water into this PMM with a mug, and the dishwasher showed 15. I don’t know what to do. There is no water in the car, but it tries to suck it in with the compressor. I think it has something to do with the aquastop. Please help me, how can I make error e 15 disappear, the tap on the display disappear, and the PMM work?

Marina · Post by **Marina** » 30 Dec 2015, 22:26

Thanks for the advice. The faucet in the kitchen broke, water flowed like a fountain, somehow got onto the machine (the machine is built-in), and after turning it on, error E15 appeared. On advice from the forum, we tilted the machine, water poured out and..... THE MACHINE WORKED, THANK YOU!

Guest · Post by **Guest** » 04 Jan 2016, 14:05

Thanks everyone!!!
It helped!!!

P/s
Error E 15, the drain worked properly, the programs did not switch (the buttons did not respond) I tried turns off for a long time time from the network.

Guest · Post by **Guest** » 06 Jan 2016, 13:33

Hooray!!! Thanks a lot!! pulled out... tilted.... EARNED!!!

And it turns out that PMM don’t like dishes with a frozen soap base.... THE FOAM CAME OUT( .. LIKE SOME FOAM PARTY...

Guest · Post by **Guest** » 08 Jan 2016, 15:43

Help! E15 keeps popping up for me! At the beginning it was once every six months, but now almost every day. You can pump and shake it every time, but this is not right, apparently something is already serious.

Guest · Post by **Guest** » 18 Jan 2016, 01:59

This error occurs when water leaks either into the bottom pan (for example, through the gutter from the front door and bottom seal, or from under pump seals, or at hose connections), or when the permissible level in the side tank drain channel is exceeded (although this is in theory first it should show a drain error E24, but whether this will cause a leak into the pan is completely unclear). And it is not the error that should be eliminated, but the cause of its occurrence (a large tilt forward and leakage through the door - by leveling it, sealing the seals will help in case of leaks at the connections, etc.). We had an E15 error, which was eliminated by tilting and/or opening the door, but then another appeared (E27, possibly), and eventually the heating element stopped heating (E09). So be careful...

visitor 08 · Post by **visitor 08** » 31 Jan 2016, 10:10

Bosch SMS 53M08EU. Problem: Error E15. The pump is running and trying to drain the water.
Solution. I read the advice. He pulled it out and shook it.
Result. It works.
Thanks everyone!

Basil · Post by **Basil** » 31 Jan 2016, 13:17

bosch spv69t70ru/01 error e015 came on because of feri (poured it stupidly), tilting helped, thank you.

Guest · Post by **Guest** » 02 Feb 2016, 13:26

The number with the slope helped

cheers

Guest · Post by **Guest** » 02 Feb 2016, 13:53

thanks everyone!!! tilt rules!

Guest · Post by **Guest** » 02 Feb 2016, 17:02

Thanks for the tips!!

Error E15 appeared on the built-in machine (my daughter poured AOS detergent instead of tablets, the foam was through the roof and the machine stuck near the door). pulled it out and tilted it to the sides, excess water apparently flowed out of the pan, turned it on - everything worked!

natalia · Post by **natalia** » 09 Feb 2016, 20:28

thanks everything worked

Slv · Post by **Slv** » 16 Feb 2016, 09:29

If there is water in the pan, it is better to turn off the machine and look for a leak. My machine first got error E15, I dried the pan. Then a floating error appeared with the flow distributor, and then the heater broke. As a result, having disassembled the machine, I saw that water was flowing from under the gasket at the junction of the bottom of the tank and the plastic cup on which the heater and pumps hang. Water got on the flow heater and it burned out. As a result, I had to buy a heater with a pump, since they come in one housing for $200. The solution is to coat it with sealant for 100 rubles. gasket

Vladimir · Post by **Vladimir** » 18 Feb 2016, 19:33

Bosch SMV40L00RU/25 built-in.E 15 came out, I didn’t even understand when, I came with the children from a party and heard that the car was draining the water, TRYING TO DRAIN THE WATER AND WOULDN’T GET NEW WATER, I turned off the electricity and it didn’t help! The car seemed to malfunction (((I typed Bosch e15 in the search engine and here I am with you)))) Thanks for the advice, I, like many others, unscrewed the fasteners, pulled out the car, tilted it and the error went away, But let me think I’ll run it in a rinse, installed it in its normal place, screwed it in, installed the kitchen screen below, opened the door and IT CAME OUT AGAIN!!! !!)))((((((((((((((( YOU DEAR FRIENDS PROBABLY ALREADY UNDERSTAND THAT LIKE EVERY RUSSIAN MAN I SWORE))) I HAD TO REPEAT EVERYTHING!! SO THIS IS MY ADVICE GUYS BEFORE BEFORE INSTALLING IT BACK AFTER ROCKING THE MACHINE AND REMOVING E15, RINSE IT FOR ONLY HALF AN HOUR AND !GOOD LUCK TO EVERYONE.

Jelena · Post by **Jelena** » 22 Feb 2016, 21:20

Thank you
tilted error reset

Tatiana · Post by **Tatiana** » 23 Feb 2016, 19:25

I searched for what to do with this error E15, I’ve already checked all the hoses, and the wiring....it’s on and that’s it

I typed for luck I was searching on the internet and came across this page
Thank you very much for the tip - tilt/stagger the dishwasher. Everything worked

Guest · Post by **Guest** » 24 Feb 2016, 10:00

Thank you!!!!!!!!!!!!! The tilt is working!!!!!!!!!!!!!!!!!!!The machine is working!!!!!!!!!!!!!!!!!!!!

Bosch SPS53E02RU error E15 - Page 2

Bosch SPS53E02RU error E15 ⇐ Bosch

Quick Reply