Dishwasher gorenje GV51211

Dishwasher gorenje GV51211 ⇐ Burning

Post Reply Previous topic Next topic

1 post • Page 1 of 1

Hope)))

Quote

Post by Hope))) » 24 Aug 2021, 23:11

Hello. Dishwasher gorenje GV51211 at the end of operation, two modes flash: 90 minutes and quick wash. What to do?

1629839516

Hope)))

Hello. Dishwasher gorenje GV51211 at the end of operation, two modes flash: 90 minutes and quick wash. What to do?

Post Reply Previous topic Next topic

1 post • Page 1 of 1

Quick Reply

Subject:

Username:

Change Text Case:

Smilies

View more smilies

This reply contains at least one attachment.

If you wish to attach one or more files enter the details below. You may also attach files by dragging and dropping them in the message box.

Maximum filesize per attachment: 15 MiB.

Filename:

File comment:

Filename	File comment	Size	Status

Similar Topics

Replies

Views

Last post

Gorenje gv66161 dishwasher does not complete the program

Last post by enzof « 10 Nov 2023, 19:35
Posted in Burning
Replies: 21
by enzof » 24 Oct 2017, 19:09 » in Burning

First post

Hello. Gorenje gv66161 dishwasher does not complete the program. At the same time, water remains in the car. If you turn it off and on again, the machine first drains all the remaining water, then it takes in new water and starts washing, but again it does not finish the program. If, after freezing in the middle of the program, you open and close the door again, the dishwasher clicks, then washes...

Last post

The problem was with the door lock. False door open signal. I won’t describe the details, the problem is a design feature. I solved the problem by slightly bending down the upper part of the PMM, where the lock is located. Thus, the lock dropped a couple of mm down and this is enough to avoid false triggering.

21 Replies

66829 Views

Last post by enzof
10 Nov 2023, 19:35
The gorenje gv66161 dishwasher squeezes out the rubber in the water supply pipe.

Last post by enzof « 10 Nov 2023, 19:54
Posted in Burning

by enzof » 10 Nov 2023, 19:54 » in Burning

Hi all. PMM 6 years. A couple of years ago, the water supply hose at the connection point began to leak. The problem was solved by replacing the factory wire clamp with a worm clamp. Now the rubber O-ring sealing the connection between the inlet fitting and the heat exchanger has squeezed out. There is an assumption that the flood of water has significant resistance in some place, but it is not...

0 Replies

1570 Views

Last post by enzof
10 Nov 2023, 19:54
Gorenje gv-54311

Last post by winmd « 05 Dec 2019, 19:37
Posted in Burning

by winmd » 05 Dec 2019, 19:37 » in Burning

Good day.
Until recently, my PMM Gorenje gv-54311 worked properly. But suddenly, at one moment, something happened to her that I had never seen before. The machine turns on as usual with the touch button, calmly allows you to select a program, but when you close the lid, the program does not start. At the same time, the machine signals that its lid is supposedly open. The machine does not produce...

0 Replies

22963 Views

Last post by winmd
05 Dec 2019, 19:37
I don’t know what to do gorenje gv64311

Last post by Guest « 27 Nov 2018, 06:37
Posted in General questions about dishwashers

by Guest » 27 Nov 2018, 06:37 » in General questions about dishwashers

The touch program switch button does not perform its functions. When pressed, it functions as an on/off button. The power button itself performs the same functions. Before this, error 04 was displayed: water in the sump. I pulled out the car, tilted it on its side to drain the water, and everything was fine. I washed one cycle and this bullshit started with the button. Help me what to do????

0 Replies

27240 Views

Last post by Guest
27 Nov 2018, 06:37
Water in the pan GORENJE GV 64311

Last post by andrey.r « 29 Sep 2016, 06:29
Posted in Burning

by andrey.r » 29 Sep 2016, 06:29 » in Burning

Hello!
I encountered the following problem.
Water accumulates in the tray in the dishwasher. Immediately after washing there is no water, if you turn off the valve on the water supply, then everything seems to be fine (by the way, that’s what it says in the instructions). But because I usually run the washer at night, then by the morning the tray is full. By the way, I noticed that it even...

0 Replies

38631 Views

Last post by andrey.r
29 Sep 2016, 06:29

Return to “Burning”